Skip to main content
Fair prices all year round instead of Black Friday promotions >
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT

Thin and shorter drive shaft right VW Passat Audi A3 TT TSI TFSI 1.8 joint set axle joint

  • ✓ Front axle right
  • ✓ VW Passat, Audi A3 TT TSI TFSI, Seat, Skoda
  • ✓ OE number Audi: 8J0407272H, 8J0407272T

Thin drive shaft for VW Passat Audi A3 TT TSI TFSI and many more. models. Essential if you want to lower your vehicle to the extreme! The shafts are 26 mm thick, are made from a single piece of high-strength steel and are solid shafts, making them suitable for performance-enhanced engines.

Suitable for the following cars:

  • Skoda Octavia II Kombi  1.8 TSI
  • Skoda Octavia Superb II Kombi 1.8TSI
  • Skoda Superb II 1.8TSI
  • Seat Leon 1.8 TSI
  • Seat Toledo III 1.8TSI
  • Audi A3 1.8 TFSI
  • Audi A3 Cabriolet 1.8 TFSI
  • Audi TT 2.0 TFSI
  • Audi TT Roadster 1.8 TFSI 2.0 TFSI
  • Audi A3 Sportback 1.8 TFSI
  • VW Passat Variant 1.8TSI
  • VW Passat CC 1.8TSI
  • VW CC 1.8 TSI

With our significantly thinner and extremely stable drive shaft, you can avoid the common problem
problem of the drive shaft hitting the body when the vehicle is lowered.

It is important that no excess pressure is created in the sleeve when installing the new drive shaft. You can see how to prevent this in our installation instructions (click here).

Installing the thinner drive shaft saves you having to rework the body. This saves you time and nerves.

Important!! Our short and thin drive shaft is only suitable if the distance from the centre of the wheel to the original mudguard edge is 31.5 cm or less. If this distance is greater in your case, the shaft is too short for your vehicle

This is how you measure the distance from the edge of the mudguard to the centre of the wheel:

/814-165769-bremssatteladapapter-vw-t5-t6-bus-adapter-365x34-bremsscheibe-audi-rs5-r8-bremssattel-8-kolben--13-.jpeg

Article data:

Installation side: Front axle right
Length:         796 mm
Thread size: M16x1.5
Sealing ring diameter: 59,5 mm
Outer gearing wheel side  36
Joint diameter on gearbox side: 108 mm
Number of holes: 6

OE-number:

  • Audi: 8J0407272H, 8J0407272T
  • VW: 1K0407272LF, 5C0407272AC, 8J0407272H

Scope of Delivery:

  • 1x thin and short drive shaft / solid shaft including joint set / axle joints for VW Passat Audi A3 TT TSI TFSI and many more.


Our drive shafts are registration-free and therefore do not need to be registered.

Technical data:

Einbauort: vorne
Einbauort: vorne

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


  • What exactly is the point of having a shorter driveshaft?
  • As a result of lowering, the axle geometry changes and the shaft presses against the wheel bearing, exposing it to high levels of wear and, in the worst case, destroying it. It is therefore imperative to depressurize the component. This is done by shortening the trees.

  • Do reinforced driveshafts also have reinforced ball joints ?
  • The wheel-side ball joints are also reinforced, but the inner ball joints are like the standard ball joints.

  • Why are two bags of grease included in the delivery?
  • The grease is included in the scope of delivery so that it can be regreased or if the gearbox flange is open at the rear. In this case, grease must still be applied there. If the shaft is supplied completely closed, no grease is required, as this has already been done. 

  • Why are no shims (OE: 1K0407357D) for the mounting supplied as they are original?
  • We do not supply the shims, as we install the latest version of the bellows. With these, the shims are no longer required.

Questions? Click here for the contact form

Average rating of 5 out of 5 stars

Brake caliper adapter custom configurator
  • ✓ brake caliper adapter custom-made manufacturing 
  • ✓ for front und rear axle
  • ✓ information about the vehicle

€111.00*
Item number: BR1

Average rating of 5 out of 5 stars

PCD Adapter Spacer Custom-Made Manufacturing
  • ✓ to configure yourself
  • ✓ with TÜV certificate
  • ✓ best quality

€96.00*
Item number: LK1

Average rating of 5 out of 5 stars

Steel Brake Line Steel Brake Line Custom Configurator
  • ✓ Desired dimensions
  • ✓ Quickly configurable
  • ✓ Length, color and connections freely selectable

€46.95*
Item number: SF1