VW T3 BUS Rear axle brake adapter T4 Brake disc transformation Brake caliper adapter
- ✓ 280x12 7D0615601 VW BUS T4 brake disc
- ✓ 1-piston 7D0615424B VW BUS T4 brake caliper
- ✓ rear axle
€217.96*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Disc brake adapter to convert the T3 BUS to brake discs on the rear axle of the T4.
The holders are made of high-strength steel, completely galvanized.
With these adapters, both T4 brake discs, i.e. both the 280 and the 294 brake discs with T4 brake calipers can be used. When buying the components, you only have to make sure that if you want to install the 280 brake disc, for example, you also use the brake calipers and brake caliper carrier that were originally installed with this brake disc.
Advantages of this brake system:
- The remaining fading on the original brake system is gone.
- Significantly better perfomance than the standard brake system.
- The material certificate included in the scope of delivery enables entry by individual acceptance even for series vehicles
- Quick and easy assembly possible with the supplied screws
The wheel hubs must be turned off for the rear disc or can also be ordered from us.
Required material for installation:
- Brake discs from VW BUS T4 280x12 mm 15 inch VAG: 7D0 615 601
- or for 16 inch 294x13.5 OE numbers: 7D0615601C
- Brake caliper bracket from VW BUS T4 280x12 mm 15 inch VAG:7D0615425B
- oor for 16 inch OE number: 7D0615425A
- Brake calipers from the VW BUS T4 15 inch OE number: 7D0 615 424B
- or for 16 inch OE number: 7D0 615 424A
- Longer studs for the rear axle
- The following brake cable fits without modifications to the vehicle if the sleeve is laid generously at the bottom of the swing arm: Brake cable Golf 2, Jetta 2 1988-1992. Cable 1622 mm/ sheath 1221 mm, vehicles with rear disc brakes (except G60) No.: 191 609 721
Suitable adapters for the front axle are also available from us.
Scope of delivery:
- 2x conversion adapter for VW T3 to T4 brake discs for the rear axle
- Set of matching centering rings
- Complete set of high resistant srews
- Certificate of material
- Copy of the german document 'Fahrzeugschein' (equivalent with the English vehicle registration card). Proves the conformity of our product in Germany and simplifies authorization by authorities.
Tips, information and hints:
- For a better ventilation of the brake system, we recommend removing the dust cover plates and brake anchor plates.
- We can not answer generally, which rim size you can mount after your brake conversion. There are simply too many different rims.
- In rare cases it is possible that the rims touch minimal the brake caliper, then you can simply use spacers.
>> Now directly to spacers << - Install the adapter with the necessary components and then check if new brake lines are required. Because, depending on the vehicle, the lines may be too short or the line tips may not suitable. We advise you to change to steel braided brake line because of the quality and technical advantage. Specifically for this, we have developed an online brake line configurator, where you can assemble the type of steel braided brake lines you want.
Click here to go to the >> configure steel braided brake lines << - Always use the hand brake cable of the installed brake caliper. So sometimes you have to modify / adapt the new handbrake cable. For conversions, where the original caliper is used and the handbrake cable can be used, you may need to pull the cable without any other fittings (ie directly) to compensate for the long distance due to the large diameter of the large brake discs.
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
6 October 2019 16:41
Edwin T
Passgenau wie immer ,schnelle Lieferung
8 July 2022 11:27
Bas V
Good quality and fitment.
3 October 2021 17:39
Patrick W
Habe mich für dieses Produkt entschieden da die Firma für Qualität steht und Passgenauigkeit Produkt hat wie versprochen gepasst mit den Tipp sie dabei standen weil die Montage ein leichtes würde das Produkt auf jeden Fall weiterempfehlen und wieder kaufen vielen Dank
16 December 2019 20:03
Stefan A
Hallo, die Adapter machen einen sehr guten Eindruck, leider konnte ich sie noch nicht verbauen. Bin mir aber sicher das sie gut passen werden ! Gruß, Stefan
26 June 2023 15:46
Bernard B
Produit de grande qualité, usinage et finit de surface de qualité supérieur, assemblage sur mon vanagon facile, sans accroc. Merci Epitec
15 July 2022 17:58
Matheo P
Package recieved quickly and well packed All pieces fit perfectly and are well made Easy instalation Informations on the article page are perfectly correct and very easy to understand
1 April 2020 08:48
Rainer T
Everything fit perfectly!
15 July 2023 20:50
Henning S
Super produkt.
19 October 2019 20:05
Edwin T
Passgenau und superschnelle Lieferung
22 May 2020 11:34
Bruno F
Perfect FIT, i have no words for the quality of this product. Epytec best! Regards From Portugal!
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: