VW T3 4-wheel Syncro BUS conversion to Porsche brake caliper adapter brake system brake caliper adapter
- ✓ 288x25 4A0615301C 4A0615301D 4A0615301E 8E0615301Q Audi A6 / A4 brake disc
- ✓ 4-piston 996352421 / 996352422 brake caliper
- ✓ front axle
£212.84*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter for front axle brake system for T3 14 Zoll Syncro to fix brake discs typ Audi A4 A6 diameter 288x25mm in combination with Porsche 996 4 Piston brake calipers.
The advantages of this brake system are the perfect deceleration values. Furthermore, the price-performance ratio of the Porsche brake calipers and the brake discs is right.
Required components:
- rear Porsche 996 brake calipers Porsche part number 996.352.421 + 996.352.422 (Only 100% suitable with the specified Porsche calipers)
- Brake discs Audi A6 A4 288x25 OE numbers: 4A0 615 301 C (VAG), 4A0 615 301 D (VAG), 4A0 615 301 E (VAG), 8E0 615 301 Q (VAG) other comparison numbers: V10-80049 (VAICO ), 100.1216.20 (ZIMMERMANN), 100.1216.70 (ZIMMERMANN)
This brake disc system allows the installation of 15” wheel rims.
Click here for the matching adapter for the 16 inch axle article 1143 (click here)
Advantages:
- The remaining fading on the original brake system is gone.
- Significantly better perfomance than the standard brake system.
- Our adaptors do require only small rectifications on your vehicle.Therefore easily transformable in its original condition
- The registration for public road use should be no problem with correct and complete execution of the work.
Scope of delivery:
- 2 brake adapter (see photo)
- Certificate of material (Proves the conformity of our product in Germany and simplifies authorization by authorities)
- High resistant screws for fixation
- Stress analysis
Tips, information and hints:
- For a better ventilation of the brake system, we recommend removing the dust cover plates and brake anchor plates.
- We can generally not answer, which rim size you can mount after your brake conversion. There are simply too many different rims.
- In rare cases it is possible that the rims touch minimal the brake caliper, then you can simply use spacers.
>> Now directly to spacers << - Install the adapter with the necessary components and then check if new brake lines are required. Because, depending on the vehicle, the lines may be too short or the line tips may not suitable. We advise you to change to steel braided brake line because of the quality and technical advantage. Specifically for this, we have developed an online brake line configurator, where you can assemble the type of steel braided brake lines you want. Click here to go to the configurator
>> Configure steel braided brake lines <<
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Login
- Which brake pads should be used?
The original brake pads from the brake caliper, which is required for our conversion kit, must always be used.
- Can I use other brake calipers as indicated in the required components?
No, unfortunately that is not possible, the reason being that all brake calipers have different height and depth measurements. If another brake disc is installed, the brake caliper would either not fit the adapter at all or not run centrally to the brake disc. If you want to install a different brake caliper, we also have an option for you. You can have a custom-made product manufactured, check out the following link for more information:
- Can I also use other discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply that all brake calipers have different height and depth measurements. If a different brake disc is installed, the brake caliper would either not fit on the adapter at all or would not be centered with the brake disc. However, if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product produced, have a look at the following link for more information:
https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
My brake caliper is not exactly centered over the brake disc - what should I do?
If your brake caliper is not exactly centered over the brake disc, in most cases it is not a problem. Depending on the vehicle, model year, and mileage, axle tolerances can occur – and this even in newer vehicles.
The most important thing is:
👉 The brake caliper must have sufficient clearance on the left and right to the brake disc so that nothing rubs or permanently touches it.Many brake calipers also have locking bolts. It may happen that:
there is very little clearance on one side or the bolt lightly touches
while on the other side there is more play
This is generally not critical.
🔧 This is how you proceed:
Install brake pads:
First check if the brake pads can be inserted cleanly and without resistance on both sides.If everything fits:
If installation is possible without problems, you can simply gently push back the locking bolts – this usually resolves the issue.If it jams:
If the brake pads cannot be installed, or only with difficulty, on one side, action is required.In this case, you can:
slightly shim the adapter with suitable bushings to adjust the brake caliper
or – depending on the situation – slightly mill the adapter so that the brake caliper is correctly centered again
👉 The goal is always that the brake caliper is evenly aligned with the brake disc and the brake pads are seated freely and cleanly.
| Motor | Motorcode |
|---|---|
| 1.6 TD Syncro | 25|70PS(51KW) |
| 2.1 Syncro | 25|112PS(82KW) |
| 1.9 Syncro | 25|78PS(57KW) |
| 2.1 Syncro | 25|95PS(70KW) |
| Motor | Motorcode |
|---|---|
| 2.1 Syncro | 24|95PS(70KW) |
| 1.9 Syncro | 24|78PS(57KW) |
| 2.1 Syncro | 24|112PS(82KW) |
| 1.6 TD Syncro | 24|69PS(51KW) |
| Motor | Motorcode |
|---|---|
| 1.6 TD Syncro | 25|70PS(51KW) |
| 2.1 Syncro | 25|112PS(82KW) |
| 1.9 Syncro | 25|78PS(57KW) |
| 2.1 Syncro | 25|95PS(70KW) |
| Motor | Motorcode |
|---|---|
| 2.1 Syncro | 24|95PS(70KW) |
| 1.9 Syncro | 24|78PS(57KW) |
| 2.1 Syncro | 24|112PS(82KW) |
| 1.6 TD Syncro | 24|69PS(51KW) |
- ✓ 268x10 7M0615601 VW Sharan 2.8 VR6 brake disc
- ✓ 1-piston 191615423 / 191615424 Girling 38 brake caliper
- ✓ rear axle
- ✓ Quick assembly
- ✓ delivered ready to install
- ✓ great safety
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Length: 50cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ VW T2/ T3 Bus
- ✓ AFN1.9 TDI PD 116 HP engine, transverse installation
- ✓ simple engine conversion
- ✓ VW T3 Bus/Syncro TDI engine conversion
- ✓ Golf 3 starter
- ✓ 0 001 125 012/013 (2.0 KW),0 986 017 460 (2.0 KW)
- ✓ VW T2/T3 Bus
- ✓ 1.9l TDI (90PS) 1Z engines
- ✓ simple engine conversion
- ✓ gear adapter plate
- ✓ suitable for VW T3 BUS / box
- ✓ 012 Audi / VW 5-speed gearbox
- ✓ 280x12 7D0615601 VW BUS T4 brake disc
- ✓ 1-piston 7D0615424B VW BUS T4 brake caliper
- ✓ rear axle
- ✓ Tie rod end M14x1.5
- ✓ VW, Audi, Golf 1, Golf 2, Golf 3, Corrado,...
- ✓ 100% perfect fit
- ✓ 280x12 7D0 615 601 VW BUS T4 brake disc
- ✓ 1-piston 701615424 VW BUS T4 brake caliper
- ✓ rear axle
- ✓ VW T3 bus
- ✓ 012 VW / Audi 5-speed
- ✓ simple engine conversion
- ✓ drive shaft adapter
- ✓ VW T3
- ✓ 012 Audi gearbox
- ✓
- ✓ 312x25 4B0615301A Audi A4 Quattro / Audi A6 brake disc
- ✓ 1-piston 4A0615123A / 4A0615124A Audi 100 / A6 C4 Girling / Ate57 brake caliper
- ✓ front axle
- ✓ switching shaft adapter
- ✓ suitable for VW T3 Bus
- ✓ 012 Audi / VW 5-speed gearbox
- ✓ 5x112 bolt circle
- ✓ Plug & Play
- ✓ VW T3 BUS
Buy matching accessories together and buy cheaper
- ✓ 268x10 7M0615601 VW Sharan 2.8 VR6 brake disc
- ✓ 1-piston 191615423 / 191615424 Girling 38 brake caliper
- ✓ rear axle
- ✓ Quick assembly
- ✓ delivered ready to install
- ✓ great safety
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Length: 50cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ VW T2/ T3 Bus
- ✓ AFN1.9 TDI PD 116 HP engine, transverse installation
- ✓ simple engine conversion
- ✓ VW T3 Bus/Syncro TDI engine conversion
- ✓ Golf 3 starter
- ✓ 0 001 125 012/013 (2.0 KW),0 986 017 460 (2.0 KW)
- ✓ VW T2/T3 Bus
- ✓ 1.9l TDI (90PS) 1Z engines
- ✓ simple engine conversion
- ✓ gear adapter plate
- ✓ suitable for VW T3 BUS / box
- ✓ 012 Audi / VW 5-speed gearbox
- ✓ 280x12 7D0615601 VW BUS T4 brake disc
- ✓ 1-piston 7D0615424B VW BUS T4 brake caliper
- ✓ rear axle
- ✓ Tie rod end M14x1.5
- ✓ VW, Audi, Golf 1, Golf 2, Golf 3, Corrado,...
- ✓ 100% perfect fit
- ✓ 280x12 7D0 615 601 VW BUS T4 brake disc
- ✓ 1-piston 701615424 VW BUS T4 brake caliper
- ✓ rear axle
- ✓ VW T3 bus
- ✓ 012 VW / Audi 5-speed
- ✓ simple engine conversion
- ✓ drive shaft adapter
- ✓ VW T3
- ✓ 012 Audi gearbox
- ✓
- ✓ 312x25 4B0615301A Audi A4 Quattro / Audi A6 brake disc
- ✓ 1-piston 4A0615123A / 4A0615124A Audi 100 / A6 C4 Girling / Ate57 brake caliper
- ✓ front axle
- ✓ switching shaft adapter
- ✓ suitable for VW T3 Bus
- ✓ 012 Audi / VW 5-speed gearbox
- ✓ 5x112 bolt circle
- ✓ Plug & Play
- ✓ VW T3 BUS