Lightened flywheel flywheel steel light Golf 1 2 3 Scirocco 16V 020 gearbox PL KR 210mm
- ✓ 16V motors
- ✓ 210 clutch
- ✓ lightens 2.9 kg
€266.41*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Lightened high-strength steel flywheel with 210 mm diameter for all models with 020 gearbox.
Suitable for Golf II 16V , VW Scirocco 16V, VW Jetta 16V and Audi 80
Engine reference: PL, KR
Our flywheels are made of high-strength molybdenum chrome, which guarantees absolute durability even on engines above 300 HP.
Below in the suitable accessories you will find the Sachs Performance clutch pressure plate you need. You can also choose between the matching organic or racing Sachs Performance clutch disc.
Advantages of our lightened flywheel:
- our flywheel weighs only 2.9 kg, the standard wheel over 5.5 kg
- it is not necessary to send us the original steering wheel
- significantly better acceleration due to less inertia
- the engine runs faster, no loss of performance.
- suitable for motorsports, racing or serial vehicles
- lower fuel consumption
- significant reduction of the turbo lag
- precision balancing, bearings are less affected, finely balanced according to DIN ISO 1940
- including ring gear
- suitable for either a standard clutch or a high-performance clutch
- Our flywheels are registration-free as they have no direct effect on the actual performance
Delivery:
- 1x lightened high-strength steel flywheel for 020 gearbox from Golf, Scirocco, Jetta, Audi 80 16V, engines PL KR
- Installation instructions
Our lightened flywheels are registration-free and therefore do not need to be registered.
Login
30 December 2023 12:29
Philip T
Hervorragende Qualität, schnelle Lieferung und fairer Preis. Sehr zu Empfehlen
11 May 2024 05:55
Ronald B
Scheint alles Ok, noch nicht eingebaut
24 April 2022 15:55
haughhead*123
Good ebayer
26 July 2022 07:30
hopp-612
Sehr geiler Artikel sehr schöne Verarbeitung vielen Dank Verkäufer sehr empfehlenswert schneller Versand
17 May 2023 05:06
Manuela (N) T
Alles super geklappt.
25 September 2023 12:57
doil1978
Top ð
4 September 2023 12:28
Levi V
Great quality and design
30 December 2023 12:16
Philip T
Hervorragende Qualität, schnelle Lieferung und fairer Preis. Sehr zu Empfehlen
16 September 2023 08:14
JOEL M
LA FINITION
- Which screws can be used?
The original bolts can be reinstalled.
- Which clutch can be used with the Epytec flywheels?
You can continue to use the original clutch or an identical Sport / Performance clutch. Please check with the clutch manufacturer whether these are of the same design as the originals. If this is the case, then it will also fit 100%
- What is the friction coefficient of the flywheel?
In principle, the friction coefficient can be assumed to be at least the same as that of the original cast disc. Due to the higher alloyed steel, our pulleys are slightly better than the original cast pulley. Of course, the material of the friction disk also has a major influence here; this must be checked with the manufacturer of the friction disk
- What material are the flywheels made of?
The flywheel is made of 16MnCr (chromium molybdenum) steel, which means it has a density of 7.76 kg/dm³
- Does the flywheel have a TDC marking and other markings for the ignition?
The flywheel has no TDC marking, only the pin on the back, just like the original flywheel. Tip: To adopt the TDC marking, the original flywheel must be turned to the TDC point before disassembly and the new flywheel must be marked in exactly this position.
- Does the flywheel have the default unbalance or is it balanced to zero?
The flywheel is supplied with the default unbalance. Unbalance can be created as follows! We first balance the pulley to 0, then apply a test mass at the specified point, which corresponds exactly to the unbalance. The pulley is then balanced to 0 again with the test mass. If you now remove the test mass, you have exactly the specified unbalance.
- Do we only sell the ring gear / gearwheel of the flywheels?
No, we can only sell the flywheels complete.
- Why do I have to run in my clutch?
The principle of a clutch is similar to that of a brake system. The different materials / surfaces must first adapt to each other. This happens through friction. With standard clutches or organic linings, this happens relatively quickly, as the lining material is "softer" than with sintered metal linings.
- ✓ crankshaft ventilation
- ✓ VW Golf, Corrado
- ✓ PL KR, 1.8 liter engine
- ✓ PL KR motor
- ✓ 210mm clutch
- ✓ 250NM torque
- ✓ Reinforced version
- ✓ Golf 1-3 / Scirocco / Audi 80
- ✓ 430mm diameter
- ✓ PL KR motor
- ✓ 210mm clutch
- ✓ 250NM torque
- ✓ Golf 1-3 / Scirocco 16V engine
- ✓ 250NM torque
- ✓ hub profile: 18.3x20.4-24N
- ✓ Golf 1-3 / Scirocco 16V engine
- ✓ 250NM torque
- ✓ hub profile: 18.3x20.4-24N
