Audi S4 A4 B5 Brake Caliper Adapter Rear Axle Cayenne 4-piston 330x22 Brake Disc Tuning Adapter
- ✓ 330x22 4F0615601B Audi A6 brake disc
- ✓ 4-piston 955352421 / 955352422 Porsche Cayenne brake caliper
- ✓ rear axle
€358.04*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter, rear axle, on models Audi S4 A4 B5 for conversion to the Porsche Cayenne brake calipers.
Combined with the 330x22 mm brake discs from Audi A6, rear.
The Porsche calipers are connected to the hydraulics of the vehicle and can thus develop an enormous braking force. However, these do not have handbrake functions. The rear axle of Audi S4 B5 is additionally used for a handbrake brake caliper adapter. The hydraulic connection is thereby closed with a blind plug / closure cap, thus this serves only as a hand brake caliper.
Suitable for the following VW und Seat models (4WD):
- Audi A4 B5
- Audi S4 B5
Advantages of this brake system:
- top deceleration, without comparison with conventional brake discs
- perfectly matches our brake caliper adapter for the front axle
- must have for better performance
- supplied material certificate
Required components:
- Handbrake caliper original Audi S4 B5 for 22mm thick brake discs, part number: 8D0 615 424 C, 8D0 615 423 C
- Brake caliper carrier original Audi S4 B5 for 22mm thick brake discs, part number: 8D0 615 405 S
- Brake calipers from the Porsche Cayenne from the rear axle part number: (stands on the rear number on the brake calipers, distinguishes right and left calipers) 955.352.421 + 955.352.422 (only 100% suitable with the specified Porsche calipers) Brembo NR:20.7673.03
- Rear brake disc 330x22 from the Audi A6 part number: 562507JC
Delivery:
- 2x brake caliper adapters for Porsche Cayenne caliper
- 2x brake caliper adaper to adapt the hand brake caliper
- high strength mounting screws
- material certificate
- Stress analysis
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Technical data:
Login
14 May 2020 09:15
Tony M
Très satisfait et correspond à 100% a mon montage, parfait !! Livraison rapide et suivi de la commande du début jusqu'à sa livraison
8 January 2021 14:16
Patrick S
Voll zu Frieden. Top Service
23 March 2023 06:08
Lewis G
Awesome bit of kit
23 March 2023 06:08
Lewis G
Awesome bit of kit
17 September 2023 19:39
Tiago G
- Because the overall experience is awesome every time I buy from epytec. - I love everything about the product and the package. - I would recommend this item to every Audi B5 Quattro owner, it upgrades the rear brakes with one of th best you can install. - In the optimization aspect, you can insert a leftlet with install instructions, or a PDF, you can offer in the future the adapter's in different colors like an optional upgrade, BTW I will paint mine. - I choose Epytec, because German quality is incredible and there is no one else in the that make this adapter's like you do. - Skeptical, No, not a bit. - I do not have installed the kit yet because, I am still missing some bits to do the complete upgrade.
15 November 2023 08:46
William B
Quality and finish of product excellent. Shipping to UK within one week. Excellent communication for an issue which necessitates sending the adapters back for a small edit, which I have no doubt will also be a excellent experience. Highly recommended company in all regards.
30 January 2020 21:08
Flori C
Super
14 November 2020 12:46
Pierre-Jean A
Conforme à la description
7 April 2024 02:18
Gurpreet S
Install is not straight forward, but is quite easy if you have a good mechanical ability. First off one of the smaller holes beside the lower bolt hole for the porsche caliper had to be drilled out to 10mm as is was slightly off its correct location on both brackets. Once it's drilled out, the bracket bolts up correctly. Secondly, the area where the caliper bolts to the bracket needs to be slightly taller as a 7.5mm shim is required to bolt the caliper close to the centerline of the rotor. If no spacers are used, the caliper pad support pins contact the inner rotor face. (Correct rotors were used as suggested off a A6 C6 4.2L car). A 10mm longer SHCS is also then required to have proper thread engagement into the caliper bracket. Lastly the caliper carrier for the stock B5 S4 Caliper E-brake setup needs to be modified to fit between the brake rotor and caliper adapter bracket as shown in the last photo. I have not completed this step yet but will post more photos and dimensions machined off the carrier once I have it completed. Thank you for your great brackets!
31 December 2023 01:29
Sinan Y
-War das einzigste Produkt was ich so finden Konnte für mein Bremsen Umbau. -Soweit war ich ganz zufrieden. -Soweit jedem der das Bremssystem so fahren möchte. -Evt. zwei kürzere Schrauben für die Radlagergehäuse. Ragen ca. 1 Cm raus. -Viel Positives über Epytec gehört. -Nein, habe schon etliche Produkte gekauft und war immer zufrieden. -Einwandfrei. Wie ich es mir vorgestellt habe.
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ 350x32 A1764210212 Mercedes CLA 43 AMG brake disc
- ✓ 6-piston 95535142153 / 95535142253 Porsche Cayenne / VW Tuareg brake caliper
- ✓ front axle
- ✓ 360x32 8D0615302B 8E0615301AB Audi RS4 brake disc
- ✓ 8-piston 8E0615107 / 8E0615108 Audi R8 brake caliper
- ✓ front axle
- ✓ 330x32 2104212612 Mercedes CLK brake disc
- ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne brake caliper
- ✓ front axle
- ✓ 356x32 420615602F Audi R8 brake disc
- ✓ 4-piston 209815 / 42615405 Audi R8 brake caliper
- ✓ front axle
- ✓ 330x22
- ✓ 68mm centering
- ✓ 42mm height
- ✓ 330x22
- ✓ 68mm centering
- ✓ 42mm height
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ Registration-free
- ✓ Redstuff ceramic covering
- ✓ temperature up to 750°C
- ✓ Desired dimensions
- ✓ Quickly configurable
- ✓ Length, color and connections freely selectable
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ 35% better braking performance
- ✓ 75% more service life
- ✓ low dust generation
- ✓ Audi engines
- ✓ 240 clutch
- ✓ lightens 8.6 kg
- ✓ Choice of color
- ✓ ZR18 / Z18 4-piston brake calipers
- ✓ 955.352.421 / 955352421 955.352.422 / 955352422 7L6615423H / 7L6615423L / 7L6615423D / 7L6615423G
- ✓ Significantly higher boiling point
- ✓ Better pedal feel
- ✓ Suitable for the race track
- ✓ Choice of color
- ✓ ZR18 / Z18 4-piston brake calipers
- ✓ 955.352.421 / 955352421 955.352.422 / 955352422 7L6615423H / 7L6615423L / 7L6615423D / 7L6615423G
