Brake Caliper Adapter VW T5 T6 Brake Caliper Audi A6 Brake Disc 356x22 Rear Axle Tuning Adapter
- ✓ 356x22 4H0615601F Audi A6 brake disc
- ✓ 1-piston 7H0615423 / 7H0615424 VW T5 T6 brake caliper
- ✓ rear axle
€153.17*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter, rear axle, on models VW T5 and T6 transporter, for conversion to the brake discs 356x22 Audi A6, combined witht the original brake calipers.
Suitable brake caliper adapters for the front axle are linked for you below in the "Crossselling" tab!
Suitable for following vehicles:
- VW T5 transporter
- VW T6 transporter
Advantages of this brake system:
- high deceleration, also in conjunction with our rear axle braking system
- thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles
- directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems
- our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling
Required components:
- brake disc: Audi A6 356x22mm , reference 4H0 615 601 F
- for the brake discs, the bolt / pitch circle must be changed to 5x120 and the hub bore to 76.0mm (we can do this for by us)
- Brake calipers from the VW T5 T6 Bus part number: 7H0 615 423 / 7H0 615 424
- Brake caliper carrier from the VW T5 T6 Bus part number: 7H0 615 425
- we recommend using the brake caliper mounting bracket from TRW. With the original it may be that these have to be adjusted slightly (remove approx. 0.5-1mm from the mounting surface) Part number TRW: BDA585
Delivery:
- 2x brake caliper adapters for VW T5 and T6 transporter
- complete screw kit
- material certificate
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Login
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ 380x34 09A18713 Nissan GTR brake disc
- ✓ 8-piston 8E0615107 / 3D0615107A RS4 B7 / R8 brake caliper
- ✓ front axle
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ 375x36 1664210912 Mercedes Benz GL brake disc
- ✓ 6-piston 7PP615149J / 7PP615150J Cayenne 958 GTS Panamera brake caliper
- ✓ front axle
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ Length: 30cm
- ✓ M10x1 straight outside
- ✓ M10x1 straight inside
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ Registration-free
- ✓ Greenstuff sports surface
- ✓ temperature up to 650°C
- ✓ to configure yourself
- ✓ with TÜV certificate
- ✓ best quality
- ✓ 2.5L TDI engines
- ✓ lightens 8 kg
- ✓ lower fuel consumption
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ Significantly higher boiling point
- ✓ Better pedal feel
- ✓ Suitable for the race track
- ✓ brake discs pitch circle diameter / bolt circle / drilling hub bore hole custome-made
- ✓ additional 2nd hole circle / pitch circle drilled in the brake disc
- ✓ turn hub diameter up
