Caliper adapter VW Audi A3 S3 TT VW Golf 4 Bora Polo 9N Porsche 996 brake
- ✓ 312x25 8N0615301A Audi S3 / Golf 4 GTI brake disc
- ✓ 4-piston 996352422 / 996352421 Porsche 996 brake caliper
- ✓ front axle
€218.95*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter for Porsche or Brembo 4 piston brake calipers from the rear axle of the 996 in connection with the Audi 312x25 brake disc.
To be installed on the front axle of the following vehicles:
- Audi A3 (8L)
- Audi S3 (8L)
- Audi TT (8N)
- VW Golf 4
- VW Bora
- VW Beetle
- VW Polo (9N)
- VW Polo 6R WCR
- Seat Ibiza
- Seat Leon
Components required:
- Brake calipers from the Porsche 996 (rear axle) Part number: 996.352.422 + 996.352.421 (only 100% compatible with the specified Porsche calipers)
- Brake discs from the Audi S3 (8L) / Golf 4 GTI 312x25mm part NO. 8N0 615 301 A
Benefits:
- Extreme deceleration values also in connection with our rear axle brake system
- the material certificate included in the scope of delivery enables entry by individual acceptance even for series vehicles
- Directly suitable for the above-mentioned models and can therefore be easily restored to the original state at any time
- Our EPYTEC brake caliper adapters do not require your serial parts to be sent in, no welding, milling or drilling.
Delivery:
- 2x brake caliper adapter (see picture)
- Complete screw material (high strength)
- Material certificate
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
26 February 2017 17:38
golfdrengen
👌🏻👌🏻
22 January 2017 05:12
bridge-brn
Very nice eBayer with fast transaction and nice items.
14 May 2018 03:13
fastrider18
Super schneller Versand wie immer! Top!!!
13 October 2018 09:34
delboy0478
Deshalb ist der Kauf von Deutsch der beste Service, danke
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ 312x25
- ✓ 65mm centering
- ✓ 34.4mm height
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ 312x25
- ✓ 65mm centering
- ✓ 35mm height
- ✓ 312x25
- ✓ 65mm centering
- ✓ 35mm height
- ✓ 312x25
- ✓ 65mm centering
- ✓ 35mm height
- ✓ Registration-free
- ✓ Redstuff ceramic covering
- ✓ temperature up to 750°C
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ 312x25
- ✓ 65mm centering
- ✓ 34mm height
- ✓ 312x25
- ✓ 65mm centering
- ✓ 34.4mm height
- ✓ Significantly higher boiling point
- ✓ Better pedal feel
- ✓ Suitable for the race track
