Audi TTRS TT TTS 8J Passat R36 Brake Caliper Adapter to RS7 Ceramic Brake Disc 356x22
- ✓ 356x22 4G8615601 RS7 brake disc
- ✓ 1-piston 8J0615423E TTRS brake caliper
- ✓ rear axle
€165.68*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter on the models mentioned below for conversion to the large RS7 brake discs, rear axle.
Suitable for the following Quattro models :
- AUDI TT Quattro
- AUDI TT Roadster
- AUDI TT 2,0 TDI
- AUDI TT 2,0 TFSI
- AUDI TT 2,5 TFSI
- AUDI TT 3,2 V6
- AUDI TT S
- AUDI TTS
- AUDI TT RS
- AUDI TTRS
- VW Passat R36
Advantages:
- thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles
- directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems
- our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling
Required components:
- brake caliper: original TTRS , reference left: 8J0.615.423.E
- brake disc: 356x22mm RS7 rear, reference: 4G8.615.601
- Brake disc internally ventilated 356x22 from Audi A6 Part No: 4H0 615 601 F
- In the case of 9 mm rims, the handbrake cable must be turned over or the mount on the caliper reworked, otherwise the cable on the inside of the rim flange will drag
Info:
If you want to drive a cheaper brake disc, the brake disc from the Audi A6 with 356x22mm (part number: 4H0 615 601 F) will also fit. The brake discs are exactly identical in dimensions.
Delivery:
- 2x brake caliper adapters
- high strength screw set
- 2x centering ring for brake disc
- material certificate
- Stress analysis / FEM calculation for entry
Tips, information and hints:
- For a better ventilation of the brake system, we recommend removing the dust cover plates and brake anchor plates.
- We can not answer generally, which rim size you can mount after your brake conversion. There are simply too many different rims.
- In rare cases it is possible that the rims touch minimal the brake caliper, then you can simply use spacers.
>> Now directly to spacers << - Install the adapter with the necessary components and then check if new brake lines are required. Because, depending on the vehicle, the lines may be too short or the line tips may not suitable. We advise you to change to steel braided brake line because of the quality and technical advantage. Specifically for this, we have developed an online brake line configurator, where you can assemble the type of steel braided brake lines you want.
Click here to go to the >> configure steel braided brake lines << - Always use the hand brake cable of the installed brake caliper. So sometimes you have to modify / adapt the new handbrake cable. For conversions, where the original caliper is used and the handbrake cable can be used, you may need to pull the cable without any other fittings (ie directly) to compensate for the long distance due to the large diameter of the large brake discs.
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
12 November 2018 12:51
billybobbooth
fits perfect listing bit confusing but item is good quality. recommended seller
1 August 2024 10:46
Philippe B
Top parfait
21 March 2018 20:18
jorgetuning2009
5*Ebayer,recommended.
2 January 2022 21:12
Benjamin W
Extrem hochwertige Ware, mit super schneller Lieferzeit. Allen TT Fahrern die mit den Originalen Bremsen unzufrieden sind, empfehle ich dieses Produkt für den Umbau. Das Ergebnis nach dem Einbau kann sich sehen lassen.
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ 370x34 8V0615301P Audi RS3 brake disc
- ✓ 8-piston 8E0615107 / 8E0615108 RS4 B7 / R8 brake caliper
- ✓ front axle
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ for e.g. VW Golf 5, 6 Audi A3 Polo etc.
- ✓ Connection 1 M12x1 male thread bent
- ✓ Connection 2 M10x1 female thread straight
- ✓ Length 35cm long / Transparent sheathed
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ Brake force regulator Infinitely variable
- ✓ Perfectly adjustable braking effect
- ✓ suitable for all vehicles
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ 356x22
- ✓ 68mm centering
- ✓ 36mm height
- ✓ Significantly higher boiling point
- ✓ Better pedal feel
- ✓ Suitable for the race track