Drive Shaft VW Golf MK2 Syncro Golf MK3 Syncro 4 Motion Conversion Rear Haldex G60 VR6 External Joint: G60
- ✓ rear axle
- ✓ Golf 2 Syncro Golf 3 Syncro 4 motion
- ✓ External joints VR6 or G60 coarse teeth
€531.15*
- TÜV registration free
- 15 years expert knowledge
- shipping within 24h
- 2 years warranty
Drive shaft kit for the rear axle, suitable for all VW Golf MK2 Syncro and Golf MK3 Syncro. The drive shafts can be ordered with either VR6 or G60 external joints. The external joints are without ABS rings.
Absolutely necessary for the rear axle if you convert your vehicle to 4 Motion (Haldex). Suitable for the VR6, 16V, 1.8T or R32 4 Motion conversion.
It is important that when installing the new drive shaft, there is no overpressure in the sleeve / gaiter. In our installation instructions you can see how you can prevent this (click here)
With the installation of our drive shaft, you avoid many modifications and you save time.
We also have suitable engine and gearbox mounting brackets, as well as suitable adapters. Just have a look in our shop or below in the accessories.
Advantages:
- stable up to 1000 HP
- 100% fitting
- solid shaft made of special high-strength material
- easy assembly
Technical data::
- External toothing on wheel side: 22 teeth
- Internal toothing on wheel side: 30 teeth
- Seal ring diameter: 51mm
Delivery:
- 1x drive shaft kit for Golf MK2 Syncro Golf MK3 Syncro, with VR6 or G60 external joints, stable up to 1000 HP
Login
25 June 2023 12:09
synchro18t
Exactly what I needed, came in good time, will definitely buy fom again, thanks
16 April 2025 18:05
vw-forced-induction
Super quick delivery, thank you very much,
- What exactly is the benefit of a shorter drive shaft?
Lowering changes the axle geometry and the shaft presses on the wheel bearing, exposing it to high wear and possibly destroying it in the worst case. Therefore, it is absolutely necessary to relieve the pressure from the component. This is done by shortening the shafts.
- Do the reinforced drive shafts also have reinforced joints?
On the wheel side, the joints are also reinforced, but the inner joints are like the standard joints.
- Why are two bags of grease included in the package?
The grease is included so that additional greasing can be done, or if the gearbox flange is open at the back. In this case, greasing must still be done there. If the shaft is delivered completely closed, greasing is not necessary as it has already been done.
- Why are no backing plates (OE: 1K0407357D) included for mounting as they are originally available?
We do not supply the base plates, as we install the latest version of the bellows. With these, the base plates are no longer needed.
- What is the length of the drive shaft?
If you want to know the length of our drive shaft, please first look directly at the product description of the respective item. If a shaft measurement is specified there, you will find the length exactly at this point (as a pure shaft measurement).
For some drive shafts, no shaft measurement is provided in the product description. In these cases, the design of the shaft is entirely guided by the components and installation conditions described in the article. This means: The drive shaft is 100% suitable if the conversion is carried out exactly as described in the article – with the mentioned combination of axle, engine, transmission (and the other specifications from the description).
Additionally important: For many drive shafts, we require the vehicle identification number (VIN), which must be provided to us. Thus, after the order, we have a clear assignment and can ensure that you receive exactly the drive shaft that perfectly fits your vehicle and setup.
| Motor | Motorcode |
|---|---|
| 1.8 Syncro | 19E|90PS(66KW) |
| 1.8 Syncro | 1G1|98PS(72KW) |
| 1.8 GTI G60 Syncro | 1G1|160PS(118KW) |
| 1.8 GTI G60 Syncro | 19E|160PS(118KW) |
| 1.8i Cat Syncro | 1G1|90PS(66KW) |
| 1.8 Syncro | 1G1|90PS(66KW) |
| 1.8 Syncro | 19E|98PS(72KW) |
| 1.8i Cat Syncro | 19E|90PS(66KW) |
| Motor | Motorcode |
|---|---|
| 1.9 TDI Syncro | 1H1|90PS(66KW) |
| 2.9 VR6 Syncro | 1H1|190PS(140KW) |
| 1.8 Syncro | 1H1|90PS(66KW) |
| 2.0 Syncro | 1H1|115PS(85KW) |
| Motor | Motorcode |
|---|---|
| 1.8 Syncro | 19E|90PS(66KW) |
| 1.8 Syncro | 1G1|98PS(72KW) |
| 1.8 GTI G60 Syncro | 1G1|160PS(118KW) |
| 1.8 GTI G60 Syncro | 19E|160PS(118KW) |
| 1.8i Cat Syncro | 1G1|90PS(66KW) |
| 1.8 Syncro | 1G1|90PS(66KW) |
| 1.8 Syncro | 19E|98PS(72KW) |
| 1.8i Cat Syncro | 19E|90PS(66KW) |
| Motor | Motorcode |
|---|---|
| 1.9 TDI Syncro | 1H1|90PS(66KW) |
| 2.9 VR6 Syncro | 1H1|190PS(140KW) |
| 1.8 Syncro | 1H1|90PS(66KW) |
| 2.0 Syncro | 1H1|115PS(85KW) |
- ✓ For Golf 2 Corrado
- ✓ On Golf 4 Accelerator Pedal
- ✓ OE:6Q1723503K
- ✓ gearbox holder
- ✓ Golf 2, Golf 3, Passat, Corrado, Jetta, Vento
- ✓ 02m / R32 V6 1.8T 6-speed gearbox DRP DQB DXW
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 1, 2, 3, Audi A3, Seat Leon
- ✓ Conversion to 6-speed 02M,/02Q or 5-speed 02A,/02J transmission
- ✓ G60 GTI 16V engines
- ✓ 228 clutch
- ✓ lightens 4.1 kg
- ✓ Hydraulic clutch complete conversion kit
- ✓ Golf 2, 3, Corrado, Jetta, Passat 35i
- ✓ Engine conversion from the Golf 4, original pedals are retained
- ✓ Passat 35I Golf 2 GTI G60
- ✓ OE NR: 357 721 401
- ✓ Golf1 Caddy conversion
- ✓ Complete KIT
- ✓ length 1.34m
- ✓ OE NR: C357721335E
- ✓ Release lever reinforced
- ✓ G60, VR6, 2L 16V, GTI, TDI, Corrado, Golf 2/ 3, Passat
- ✓ 02A/02J gearbox
- ✓ 4x100 to 5x112
- ✓ 20mm per side
- ✓ 57.1 -> 57.1 centering
- ✓ 312x25 1J0615301AA 1J0615302A S3 / R32 brake disc
- ✓ 1-piston 1J0615123E / 1J0615124E S3 / R32 brake caliper
- ✓ front axle
- ✓ VW Golf 2, Golf 3 Passat, Corrado, Jetta, Vento
- ✓ 02a 02j 5 gear
- ✓ 1.8T 16V G60 conversion
- ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 brake disc
- ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne/ VW Tuareg brake caliper
- ✓ front axle
- ✓ 02M transmission conversion to FWD
- ✓ simple conversion
- ✓ Golf 1, Golf 2, 3, Golf 4 series
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ VW Golf 2, Golf 3 Passat, Corrado, Jetta, Vento
- ✓ Golf 3 16V, 1.8T transverse installation, Golf 4TDI
- ✓ 4 motions
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 4, Audi A3, Seat Leon, Skoda Oktavia
- ✓ 1J0721261D
- ✓ 4x100 to 4x108
- ✓ 20mm per side
- ✓ 57.1 -> 57.1 centering
Buy matching accessories together and buy cheaper
- ✓ For Golf 2 Corrado
- ✓ On Golf 4 Accelerator Pedal
- ✓ OE:6Q1723503K
- ✓ gearbox holder
- ✓ Golf 2, Golf 3, Passat, Corrado, Jetta, Vento
- ✓ 02m / R32 V6 1.8T 6-speed gearbox DRP DQB DXW
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 1, 2, 3, Audi A3, Seat Leon
- ✓ Conversion to 6-speed 02M,/02Q or 5-speed 02A,/02J transmission
- ✓ G60 GTI 16V engines
- ✓ 228 clutch
- ✓ lightens 4.1 kg
- ✓ Hydraulic clutch complete conversion kit
- ✓ Golf 2, 3, Corrado, Jetta, Passat 35i
- ✓ Engine conversion from the Golf 4, original pedals are retained
- ✓ Passat 35I Golf 2 GTI G60
- ✓ OE NR: 357 721 401
- ✓ Golf1 Caddy conversion
- ✓ Complete KIT
- ✓ length 1.34m
- ✓ OE NR: C357721335E
- ✓ Release lever reinforced
- ✓ G60, VR6, 2L 16V, GTI, TDI, Corrado, Golf 2/ 3, Passat
- ✓ 02A/02J gearbox
- ✓ 4x100 to 5x112
- ✓ 20mm per side
- ✓ 57.1 -> 57.1 centering
- ✓ 312x25 1J0615301AA 1J0615302A S3 / R32 brake disc
- ✓ 1-piston 1J0615123E / 1J0615124E S3 / R32 brake caliper
- ✓ front axle
- ✓ VW Golf 2, Golf 3 Passat, Corrado, Jetta, Vento
- ✓ 02a 02j 5 gear
- ✓ 1.8T 16V G60 conversion
- ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 brake disc
- ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne/ VW Tuareg brake caliper
- ✓ front axle
- ✓ 02M transmission conversion to FWD
- ✓ simple conversion
- ✓ Golf 1, Golf 2, 3, Golf 4 series
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ VW Golf 2, Golf 3 Passat, Corrado, Jetta, Vento
- ✓ Golf 3 16V, 1.8T transverse installation, Golf 4TDI
- ✓ 4 motions
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 4, Audi A3, Seat Leon, Skoda Oktavia
- ✓ 1J0721261D
- ✓ 4x100 to 4x108
- ✓ 20mm per side
- ✓ 57.1 -> 57.1 centering