VW T3 Bus Brake Caliper Adapter Caliper Audi Ate 57 288x25 15-inch Brake System
- ✓ 288x25 4A0 615 301 Audi A4 Quattro / Audi A6 brake disc
- ✓ 1-piston Girling / ATE 57 4A0615123A / 4A0615124A Audi 100 /A6 brake caliper
- ✓ front axle
€147.71*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
We finally designed a brake caliper adapter that be installed on the T3 2WD bus (not Syncro) under the 15-inch rims.
The adapters are mounted with 288x25 mm internally vented brake discs and with the Audi A6 calipers.
Advantages:
- top deceleration
- the system no longer warms up and no more fading
- very cheap components. you can find second-hand caliper from 49.- € / new from 70.-€
- thanks to the material certificate supplied with the order, it is possible to register your purchase
- quick and easy assembly with the supplied mounting screws
Required components:
- Brake discs 288x25 mm Audi A4 Quattro, Audi A6 z.B. OE-number:
4A0 615 301 C (VAG), 4A0 615 301 D (VAG), 4A0 615 301 E (VAG), 8E0 615 301 Q (VAG) other comparaison numbers :
V10-80049 (VAICO), 100.1216.20 (ZIMMERMANN), 100.1216.70 (ZIMMERMANN) - bracke calipers Audi 100/A6 C4 Girling/ ATE 57 reference : 4A0615123A/4A0615124A (left, right)
- Brake caliper brackets required for installing the brake system 288.Part No.4A0615125A (required because of the shorter form of these brackets)
- Hubs that are also available in our shop, item number 341. A complete kit including hub is also available in our shop, number 657
Only suitable with the 15 inch axle of T3 (you can see it with the screws fixing the calipers. The thread should be 16 mm)
Because of the thickness of the brake discs, the track is widened by 7mm for each side.
Important!!!
So that you can bleed the brake system cleanly, we recommend to mount the brake calipers reversed, i.e. to mount the left brake caliper on the right vehicle side and the right brake caliper on the left vehicle side.
Delivery:
- 1x adapter system for brake caliper
- 1x complete set of high strength screws for both sides
- 2x hub centric rings for the discs
- material certificate
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
10 May 2018 11:35
Kresimir S
Super!! Great product!!
16 January 2019 20:05
Herr A
Produkte sind technisch gut umgesetzt
19 December 2020 14:36
Christoph D
Schnelle Lieferung. Teile passen sauber.
19 November 2019 17:28
Jürgen D
Schnelle Lieferung Passgenau super Service
23 December 2020 23:09
Christoph D
Passt alles. Hotline Telefon nicht akztabel.
19 April 2024 19:22
Sérgio L
Everyting ok. Fast shipping. The material seems to be of good quality. Has not yet been installed.
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: