Steel Braided Brake Line Steel Rear Axle VW Golf 4 R32 Audi A3 S3 A1 Ibiza Polo 9N Brake Conversion
- ✓ 6-piece set
- ✓ problem-free registration
- ✓ for Golf 4 Polo 9N Audi A1 Audi A3 /S3
€224.55*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Steel braided brake line kit (6 pieces), including material certificate for easy registration. Suitable for Brembo brake system. Consersion for rear and front axle.
Suitable for the following models:
- Golf 4
- Polo 9N
- Audi A1
- Audi A3 /S3
Advantages compared to original brake lines:
- no loss of pressure when braking. Exact pressure point
- easy assembly. The original line is simply replaced by the braided steel line
- no swelling as with rubber lines
- cost savings, because the braided steel lines do not need to be changed every 3 or 5 years
- shorter braking
- protection against the rodents
- great optics
Delivery:
- 6x steel braided brake lines / steel flexible brake hoses for VW Golf MK4 Aud A3 Polo, etc...
- material certificate
We also manufacture according to desired dimensions. With our steel braided lines configurator (click here), you can configure your steel braided brake line, according to your wishes. (Length, color and connections)
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Login
23 March 2023 07:04
Cedric W
Würde sie wieder kaufen.
11 September 2021 12:50
Bruno C
Très bonne qualité
18 September 2018 22:24
Franco G
- Weil es zwar gutwar, aber nicht wie erwartet. - Innengewinde sehr grob geschnitten, was sich mir rissen am bemerkbar macht. In der Verschraubung nicht entgratet und späne drin! Hinterer Übergang zur Achse mit den Serienspangen nicht festzubekommen, hier müssen komplett andere Federspangen her, was entweder vorab erwähnt werden sollte, oder eben direkt mitliefern. - Freunden die sowas suchen - Endkontrolle (späne) - Weil nur ihr ein komplettset hattet - Ja wegen dem Gutachten - Kann ich nicht beurteilen, da zwar mitlerweile nach viel ärger (Federspangen) verbaut und Auto noch im Umbau.
- Does the steel braided brake line also fit other vehicles?
Yes, the brake line can be used in many other vehicles as well. Since almost all car manufacturers use the same size of thread for brake line fittings. Often the only difference is the concave or convex sealing surface. Our fittings are so-called hermaphrodite, which means that each fitting is suitable, concave (valley) and convex (mountain). All you have to do is measure the length and find out the thread size of the fitting you want for your line. So you can see if the line is suitable. You can find the exact details of the brake line in the product description under the technical data.
- There were 2 lens seals supplied with the steel faux lines. Where exactly are these installed?
the lens seals are always included with the orders. They are used to balance the cone, depending on the cone of the steel tube, see picture attached. With flare F you do not need the lens seals, with flare E they must be placed in the internal threads. The direction, which way around, does not matter.
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Length: 20cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Length: 17cm
- ✓ M10x1 straight inside
- ✓ M10x1 straight inside
- ✓ Bore 11mm
- ✓ 90 degree curved
- ✓ for welding
- ✓ Steering gear, axial joint, tie rod ends
- ✓ VW Golf 4 2.3 V5 4motion
- ✓ toothed
- ✓ 5x100 bolt circle
- ✓ Plug & Play
- ✓ Seat Leon / Audi A3 / Audi TT quattro
- ✓ Bore 7mm
- ✓ straight
- ✓ For welding/screwing on
- ✓ Bore 7mm
- ✓ straight
- ✓ For welding/screwing on
- ✓ Bore 11mm
- ✓ 90° bent
- ✓ for welding/screwing
- ✓ Bore 7mm
- ✓ 90° bent
- ✓ for welding/screwing
- ✓ Inner diameter 9mm
- ✓ outer diameter 25mm
- ✓ rubber ring
- ✓ Inner diameter 7.5mm
- ✓ outer diameter 24mm
- ✓ rubber ring
- ✓ 1.6l 16V engines
- ✓ 220 clutch
- ✓ lightens 3.3 kg