VW Golf MK7 Touran Audi A3 Q3 Brake Caliper Adapter 360x32 Disc Audi RS4 B5 Brembo 8-piston Brake Caliper Audi RS5 Brake System

✓ 360x32 8D0615302B Audi RS4 B5 brake disc
✓ 8-piston 8E0615107 / 8E0615108 Audi RS4 RS5 brake caliper
✓ front axle

€198.40*

Prices incl. VAT plus shipping costs

Available

Product number: 584

Delivery by Tuesday, 24.06.2025 if you order within the next 14 Hours.

Product number: 584

Weight: 2.63 kg

Brake caliper hole spacing: 200

Hole spacing steering knuckle: 146

Mounting location: front

Your benefits

Easy TÜV registration
Quality Made in Germany
Fair prices without middlemen you buy directly from the manufacturer and developer of the product
Worldwide no. 1 in tuning adapters
15 years expert knowledge
10 years warranty

Brake caliper adapter, front axle, on models VW Golf MK7 Audi A3 for conversion to the Audi RS4 RS5 8-piston Brembo calipers, combined with the Audi RS4 B5 360x32mm brake discs.

Suitable for the following vehicles with aluminum axles:

Audi A3
Audi A3 Cabriolet
Audi Q2
VW Arteon
VW Golf Sportsvan
VW Golf MK7
VW Golf 7 Variant
VW Passat Variant
VW Tiguan
VW Touran
Seat Ateca
Seat Leon
Seat Leon ST
Skoda Octavia 3
Skoda Octavia 3 estate
Skoda Superb 3
Skoda Superb estate 3

Advantages of this brake system:

high deceleration, also in conjunction with our rear axle braking system
thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles
directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems
our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling

Required components:

brake caliper: Audi RS4 RS5 8-piston original Brembo, reference left 8E0615107 right E0615108
brake disc: Audi RS4 B5 360x32mm, reference 8D0615302B or RS4 B7 365x34mm, reference8E0615301AB
(when the 365 discs are installed, it is necessary to place washers on the brake caliper mount so that the brake disc size is compensated)

Delivery:

2x brake caliper adapters for VW Golf MK7 Audi A3 series
material certificate
high-strength mounting screws

Tips, information and advice:

To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel

Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.

We provide a material certificate for this adapter, allowing the TÜV inspector to easily register the adapter.

Technical data:

Brake caliper hole spacing: 200

Hole spacing steering knuckle: 146

Mounting location: front

Brake caliper hole spacing: 200

Hole spacing steering knuckle: 146

Mounting location: front

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

email address

password

or Register with...

No reviews found. Share your insights with others.

Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:

Questions? Click here for the contact form