Skip to main content
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT

Installation instructions article 183 VR6 conversion to Golf 1 

here you can read , how to install the VR6 engine  step by step,  in conjunction with the transmissions 02A, 02J in a VW Golf 1 / Caddy 14d / Scirocco Jetta 1 & 2 .

Here you can see the general positions at which the Epytec tuning adapters are mounted on the engine and gearbox

Important!!

Please do not press in the rubber mounts immediately, always mount the engine and gearbox mounts first and hang the engine with the gearbox in the body and align it as desired, then check how the bearings have to be pressed in so that there is no tension and everything fits properly. The background is that the bearings are eccentric and no body is the same, each has slightly different dimensions or some have already had an accident, etc. These differences can be perfectly compensated for by the eccentric bearings.

When it belongs to  bearings for the VR6 conversion, we unfortunately cannot recommend original rubber bearings, as they are simply too weak for the heavy engine and crumble after six months of driving at the latest. That's why we have included extra high-strength rubber bearings with a Shore hardness of 65-70 (much more stable than the originals) in our range for this purpose. 
 Despite the harder strength, these bearings have the same comfort as original bearings and are significantly softer than the hard PU bearings.
 It is of course up to you which bearings you use, but we have done many long-distance tests with these bearings and they still hold up perfectly after all this time.

click here to the rubber bearings 

Clutch actuation Conversion of the clutch, here we have two different variants 

Hydraulic clutch controls are installed in the new gearboxes, e.g. from the Golf 4. But since the Golf 1 has mechanical clutch cables, we have our bearing block set with a matching clutch cable.

With this conversion set, the conversion to a mechanical clutch is very simple.

click here to the mechanical clutch

Alternatively, you can also switch to the hydraulic clutch without having to change the pedals. We have developed a hydraulic clutch conversion kit for this purpose.
The huge advantage of our conversion set is that the original pedals from the VW Golf 1, Caddy 14D, Scirocco, etc. can be retained and do not have to be laboriously converted.
Furthermore, stepping on the clutch is much easier than if you convert to a cable.
In the matching accessories for this article, we also offer the matching slave and master cylinder.

click here to the hydraulic clutch 

To connect the different diameters of the water hoses of the heater (Golf 1 to VR6) we have developed a small adapter to make your life easier

click here to the heating hose adapter 

Plug assignment plan for conversion

Tipp!!

Varta has a C30 battery with 54 AH, which is extremely small. This then fits without any problems in the original position without changing anything. 
This means that a large cooler, e.g. from the Passat 32B, 1.6 or 1.8 with an air conditioner with a width of 700mm, can also be used.


If necessary, I would leave this outside... it puts you off again... I think, how do you see it?

Topic TÜV registration: 

If the TÜV acceptance is to be carried out, the following conditions apply:

Disc brake system front and rear from the G60/16V with brake booster, master brake cylinder and throttles, front disc internally ventilated with a diameter of 280 mm. Matching adapters + larger brake systems such as on Porsche can be found in our shop.

Matching adapter for the rear axle to G60

wishbone reinforced by welded sheet metal strips (click here

Wishbone struts at the front below and stabilizers at the front and rear are required

On the front axle must be installed springs with a correspondingly higher load  e.g. a screw -on chassis from Golf 1 with springs for Golf 3 VR6

The tires must have sufficient load capacity and the speed rating V.

Exhaust system from the Scirocco 16V with the cat. belonging to the VR6 engine. Loud "Group A" systems should be avoided, as the EURO 1 standard also stipulates noise emissions.

Air filter unit in a closed box, or a K&N air filter with a certificate for Golf 3 VR6 and a corresponding bracket.

The conversion should be done properly, which means that there are no cables, hoses or additional components lying around loosely in the engine compartment and over time scraping, tearing or falling off. In your own interest, cable connections should be made with a soldering iron and shrink tubing.

Tipps, that is often forgotten !!

  • Forgotten split pins on tie rod ends, brake lines or cables not attached or rubbing against moving parts
  • Servo hoses not fastened or grinding, no washers or self-locking nuts installed at the designated points
  • Rear wheel bearing play too large
  • Rubber boots on drive shafts or steering defective etc. 

Important !!

Please check before acceptance! The TÜV carries out random AU inspections. If the examination is passed, your Golf 1 will be classified as EURO 1. It is advisable to bring a valid AU certificate carried out with the new engine. It is recognized and acceptance cannot fail due to a defect in the engine.

Average rating of 4.8 out of 5 stars

VW Golf MK1 Caddy Scirocco Jetta VR6 R32 Engine Mounting Bracket Holder Support Engine Conversion
  • ✓ Golf 1, Caddy 14d, Scirroco 1, Jetta 1&2
  • ✓ 02A/02J gearbox
  • ✓ VR6 R32 engine conversion

€222.85*
Item number: 183

Do you have any questions or requests? 

Then simply contact us via our contact form (click here)

Tuning Adapter Topseller

Average rating of 4.9 out of 5 stars

Audi A3 S3 TT VW Polo 6R VW Golf MK4 Bora Porsche Brake Caliper Adapter
  • ✓ 323x28 1ML615301 Seat Leon Cupra R brake disc
  • ✓ 4-piston 955352421 / 955352422 Porsche Cayenne brake caliper
  • ✓ front axle

€155.28*
Item number: 596

Average rating of 4.9 out of 5 stars

Audi TT A3 S3 VW Golf Polo 6r WRC Brake Caliper Adapter Cayenne ZR17 Brake System 334x32
  • ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 R32 brake disc
  • ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne / VW Tuareg brake caliper
  • ✓ front axle

€148.46*
Item number: 403

Average rating of 4.8 out of 5 stars

BMW E30 Wheel Hub Conversion PCD 5x120 E36 E46 Adapter Spacer Front 5 Hole Hub
  • ✓ Conversion bolt circle 5x120
  • ✓ wheel hub E36 / E46
  • ✓ front axle

€105.75*
Item number: 126

Average rating of 4.5 out of 5 stars

Brake caliper adapter BMW 1 series 2 series 3 series 4 series F20 F21 F22 F23 F30 F31 F32 F33 F34 F36 convertible coupe BMW M2 M3 380x30 brake disc 4 piston brake caliper tuning adapter
  • ✓ 380x30 34112284809 34112284810 Brake disc
  • ✓ 4-piston F20 34116799465 34116799466 Brake calipers
  • ✓ front axle

€161.21*
Item number: 1108

Average rating of 4.9 out of 5 stars

Brake Caliper Adapter Porsche for Audi TT A3 S3 VW Golf Polo
  • ✓ 334x32 8N0615301B 1J0615301 R32 brake disc
  • ✓ 6-piston Z18 95535142153 / 95535142253 Cayenne brake caliper
  • ✓ front axle

€160.71*
Item number: 143

Average rating of 4.1 out of 5 stars

Brake Caliper Adapter VW T5 T6 Porsche Panamera 87mm Mercedes Benz Brake Disc 375x36 Front Axle
  • ✓ 375x36 1664210912 Mercedes Benz GL brake disc
  • ✓ 6-piston 7PP615149J / 7PP615150J Cayenne 958 GTS Panamera brake caliper
  • ✓ front axle

€214.39*
Item number: 942

Average rating of 4.9 out of 5 stars

Golf Corrado VR6 16V Brake calipers adapter R32 S3 TT 1,8T 312x25 334x32
  • ✓ 312x25 1J0615301AA 1J0615302A S3 / R32 brake disc
  • ✓ 1-piston 1J0615123E / 1J0615124E S3 / R32 brake caliper
  • ✓ front axle

€34.64*
Item number: 575

Average rating of 4.9 out of 5 stars

Golf MK1 Caddy Brake Caliper Adapter G60 S2 Adapter Brake System
  • ✓ 280x22 535615301 G60 brake disc
  • ✓ 1-piston Girling 54 443615124A / 443615123A brake caliper
  • ✓ front axle

€105.70*
Item number: 216

Average rating of 4.9 out of 5 stars

Mercedes Benz C63 W204 Brake System 390x36 AMG Brake Caliper Adapter 6-piston
  • ✓ 390x36 A2314211812 / A2314211812 Mercedes AMG C63 brake disc
  • ✓ 6-piston A2044214798 / A2044214898 Mercedes CLS 63 AMG brake caliper
  • ✓ Front axle

€214.97*
Item number: 890

Average rating of 4.9 out of 5 stars

VW Golf 3 Brake Caliper Adapter Porsche Vr6 GTI Passat 35 16V ZR17 ZL17 Front axle Brake System 334x32
  • ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 brake disc
  • ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne/ VW Tuareg brake caliper
  • ✓ front axle

€133.47*
Item number: 284