Brake Caliper Adapter Audi A6 2,7T A4 quattro 1,8T VW Passat Audi R8 VW Phaeton Brembo 8-piston Caliper 365x34mm Brake Disc Front Axle
- ✓ 365x34 8T0615301 Audi R8 / VW Phaeton brake disc
- ✓ 8-piston 3D0615107A / 3D0615108A Audi R8 / VW Phaeton brake caliper
- ✓ front axle
€355.79*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter, front axle, on models Audi A6 C5 for conversion to Audi R8 / VW Phaeton brake system with the 8-piston Brembo brake caliper, combined with the 365x34mm brake discs.
Suitable for the following vehicles:
- Audi A6 C5
- Audi A4 B5
- VW Passat B5
Advantages of this brake system:
- high deceleration, also in conjunction with our rear axle braking system
- thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles
- directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems
- our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling
Required components:
- brake caliper: original Audi R8 8-piston, reference 3D 0615 107A / 3D0 615 108A, Brembo reference 20767502
- brake disc: Audi R8 365x34mm, reference 8T0615301
Lieferumfang:
- 2x brake caliper adapters for Audi A6 C5, Audi A4 B5, VW Passat B5
- high-strength mounting screws
- material certificate
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
20 December 2020 18:11
senatorls1
Heute ist nicht aller Tage, bei dir Kauf ich wieder keine Frage!!!!!!!!!!!!!!!
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ to configure yourself
- ✓ with TÜV certificate
- ✓ best quality
- ✓ 335x22 3D0615601 Audi S8 brake disc
- ✓ 4-piston 996352421 / 996352422 Porsche Boxter brake caliper
- ✓ rear axle
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ Length: 63cm
- ✓ M10x1 outside 45° curved
- ✓ M10x1 inside straight
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ 365x34
- ✓ 68mm centering
- ✓ 52mm height
- ✓ Registration-free
- ✓ Redstuff ceramic covering
- ✓ temperature up to 750°C
- ✓ Bushing wishbone front axle 4D0407693AC
- ✓ Audi A4 A6 A8, VW Passat, Skoda Superb, Seat Exeo.......
- ✓ Made in Germany
- ✓ Significantly higher boiling point
- ✓ Better pedal feel
- ✓ Suitable for the race track