Fine Thin Drive Shaft right VW Golf MK1 Scirocco Jetta Caddy 1 Axle Joint
- ✓ Front axle right
- ✓ Golf 1 Cabrio, Scirocco 1, Caddy Jetta
- ✓ Registration free
£172.05*
| Name | Title | Surcharge |
|---|---|---|
| Chassis number: |
- 30 days money back guarantee
- shipping within 24h
- 15 years expert knowledge
- 2 years warranty
Fine drive / transmission shaft for VW Golf MK1, Scirocco 1, Jetta, Caddy models. Absolutely necessary when lowering! The shaft is manufactured in one piece and is a complete drive shaft. Thus also suitable for high-performance engines.
Suitable for the following vehicles:
- Golf MK1
- Scirocco 1 ( 53B )
- Jetta
- Caddy
Thanks to our thin and extremely stable transmission / drive shaft, you avoid many problems at the body that usually appear during a chassis lowering. With the installation of our drive shaft, you avoid many modifications and you save time.
It is important that when installing the new drive shaft, no excess pressure is created in the sleeve. In our installation instructions you can see how to prevent this (click here).
Important!! Our short and thin drive shaft is only suitable if the dimension from the wheel center to the original fender edge is 31.5cm or smaller. If this distance is higher, the shaft is too short for your vehicle.
This is how you measure the distance from the fender edge to the wheel center:
Technical data:
| assembly side: | front axle right |
| length:; | 745,0 mm |
| thread: | M20x1.5 |
| seal ring-Ø: | 53,20mm |
| PCD-Ø: | 78 mm |
| joint diameter, differential side: | 92 mm |
| number of drill holes: | 6 |
| external toothing wheel side: | 22 |
| chassis: | for vehicles with low-profile chassis |
| joint diameter wheel side: | 90,0 mm |
Delivery:
- 1x fine thin drive / transmssion shaft, inclusive axle joint, Golf MK1,Scirocco 1, Jetta, Caddy
Our drive shafts are registration-free and therefore do not have to be registered.
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Login
- What exactly is the benefit of a shorter drive shaft?
Lowering changes the axle geometry and the shaft presses on the wheel bearing, exposing it to high wear and possibly destroying it in the worst case. Therefore, it is absolutely necessary to relieve the pressure from the component. This is done by shortening the shafts.
- Do the reinforced drive shafts also have reinforced joints?
On the wheel side, the joints are also reinforced, but the inner joints are like the standard joints.
- Why are two bags of grease included in the package?
The grease is included so that additional greasing can be done, or if the gearbox flange is open at the back. In this case, greasing must still be done there. If the shaft is delivered completely closed, greasing is not necessary as it has already been done.
- Why are no backing plates (OE: 1K0407357D) included for mounting as they are originally available?
We do not supply the base plates, as we install the latest version of the bellows. With these, the base plates are no longer needed.
- What is the length of the drive shaft?
If you want to know the length of our drive shaft, please first look directly at the product description of the respective item. If a shaft measurement is specified there, you will find the length exactly at this point (as a pure shaft measurement).
For some drive shafts, no shaft measurement is provided in the product description. In these cases, the design of the shaft is entirely guided by the components and installation conditions described in the article. This means: The drive shaft is 100% suitable if the conversion is carried out exactly as described in the article – with the mentioned combination of axle, engine, transmission (and the other specifications from the description).
Additionally important: For many drive shafts, we require the vehicle identification number (VIN), which must be provided to us. Thus, after the order, we have a clear assignment and can ensure that you receive exactly the drive shaft that perfectly fits your vehicle and setup.
| Motor | Motorcode |
|---|---|
| 1.6 D | 17|54PS(40KW) |
| 1.5 | 17|70PS(51KW) |
| 1.6 GTI | 17|110PS(81KW) |
| 1.8 GTI | 17|112PS(82KW) |
| 1.1 | 17|50PS(37KW) |
| Motor | Motorcode |
|---|---|
| 1.8 | 155|112PS(82KW) |
| 1.6 | 155|75PS(55KW) |
| 1.5 | 155|70PS(51KW) |
| 1.8 | 155|90PS(66KW) |
| 1.8 | 155|95PS(70KW) |
| Motor | Motorcode |
|---|---|
| 1.6 | 14|75PS(55KW) |
| 1.6 D | 14|55PS(40KW) |
| Motor | Motorcode |
|---|---|
| 1.5 | 16|70PS(51KW) |
| Motor | Motorcode |
|---|---|
| 1.8 | 53B|95PS(70KW) |
| Motor | Motorcode |
|---|---|
| 1.6 D | 17|54PS(40KW) |
| 1.5 | 17|70PS(51KW) |
| 1.6 GTI | 17|110PS(81KW) |
| 1.8 GTI | 17|112PS(82KW) |
| 1.1 | 17|50PS(37KW) |
| Motor | Motorcode |
|---|---|
| 1.8 | 155|112PS(82KW) |
| 1.6 | 155|75PS(55KW) |
| 1.5 | 155|70PS(51KW) |
| 1.8 | 155|90PS(66KW) |
| 1.8 | 155|95PS(70KW) |
| Motor | Motorcode |
|---|---|
| 1.6 | 14|75PS(55KW) |
| 1.6 D | 14|55PS(40KW) |
| Motor | Motorcode |
|---|---|
| 1.5 | 16|70PS(51KW) |
| Motor | Motorcode |
|---|---|
| 1.8 | 53B|95PS(70KW) |
- ✓ Front axle left
- ✓ Golf 1 Cabrio, Scirocco 1, Caddy Jetta
- ✓ Registration free
- ✓ Brake force regulator 3/15
- ✓ conversion to G60 16V VR6
- ✓ OE NO: 486145
- ✓ Complete set of 4
- ✓ Reinforced Shore 65-70
- ✓ Golf 1 Caddy 14D Scirocco Jetta
- ✓ Golf 1, Caddy 14d, Scirroco 1, Jetta 1&2
- ✓ 02A/02J gearbox, 1.8T from Golf 4
- ✓ Golf 1 bearing outer diameter 64mm
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 1, 2, 3, Audi A3, Seat Leon
- ✓ Conversion to 6-speed 02M,/02Q or 5-speed 02A,/02J transmission
- ✓ 280x22 535615301 G60 brake disc
- ✓ 1-piston Girling 54 443615124A / 443615123A brake caliper
- ✓ front axle
- ✓ Hydraulic clutch complete conversion kit
- ✓ Golf 1, Golf 1 Cabrio, Caddy 14D, Jetta, Scirocco
- ✓ Engine conversion from the Golf 4, original pedals are retained
- ✓ Complete KIT
- ✓ length 1.34m
- ✓ OE NR: C357721335E
- ✓ Registration free
- ✓ For shift linkage
- ✓ stainless steel
- ✓ 4x100 to 5x112
- ✓ 20mm per side
- ✓ 57.1 -> 57.1 centering
- ✓ For Golf 1 Caddy
- ✓ On Golf 4 Accelerator Pedal
- ✓ OE:VW 1J1721503E
- ✓ VW Golf 2, Golf 3 Passat, Corrado, Jetta, Vento
- ✓ 02a 02j 5 gear
- ✓ 1.8T 16V G60 conversion
- ✓ Golf 1, Caddy 14d, Scirroco 1, Jetta
- ✓ 02A/ 02J 5-speed, 02M 6-speed gearbox
- ✓ 1.8T, 1.9TDI, G60
- ✓ Golf 1, Scirocco, Caddy 14D
- ✓ 1.8l 20vT, 1.9 TDI
- ✓ simple engine conversion
- ✓ 02M transmission conversion to FWD
- ✓ simple conversion
- ✓ Golf 1, Golf 2, 3, Golf 4 series
- ✓ mechanical tension roller
- ✓ 1.8T engine conversion
- ✓ Golf 1, Scirocco, Caddy 14d
- ✓ electric brake light adapter
- ✓ Golf 1, Caddy 14D, Scirocco, Jetta
- ✓ easy conversion
- ✓ Length: 57cm
- ✓ M10x1 curved on the outside
- ✓ M10x1 straight on the inside
- ✓ Hydraulic clutch slave cylinder
- ✓ Golf 4, Audi A3, Seat Leon, Skoda Oktavia
- ✓ 1J0721261D