VVW Passat R36 B6 Type 3C, Golf 5 R32, Golf 6 R and Golf 7 R 4 Motion Adapter Brake Caliper Adapter Rear Axle 310x22 Brake Disc Tuning Adapter
€152.76*
- Einfache TÜV Eintragung
- Qualität Made in Germany
- Faire Preise ohne zwischenhandel du kaufst direkt beim Hersteller und Enwickler des Produktes
- Weltweit Nr 1 in Sachen Tuning Adapter
- 15 Jahre Expertenwissen
- 10 Jahre Garantie
Brake caliper adapter, rear axle (steel knuckle), on models mentioned below, to install the 356x22 mm A6 brake discs, combined with the original caliper.
Suitable for following vehicles with original 310x22 brake discs :
- VW Passat R36
- Golf 5 R32
- Golf 6 R
- Touran
- Caddy
Advantages:
- high deceleration
- thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles
- directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems
- our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling.
Required components:
- internally vented brake discs 356x22 from Audi A6 reference: 4H0 615 601 F
- original brake caliper and pads
Info:
If you want to run a perforated brake disc, the Wave brake disc from the Audi RS7 with 356x22mm (part number: 4G8.615.601) will also fit, as the Audi S6 S7 S8 brake disc is not available perforated. The brake discs are otherwise exactly identical in dimensions.
Delivery:
- 2x brake caliper adapters VW Passat R36
- matching centering rings
- fastening material
- material certificate
Tips, information and hints:
- For a better ventilation of the brake system, we recommend removing the dust cover plates and brake anchor plates.
- We can not answer generally, which rim size you can mount after your brake conversion. There are simply too many different rims.
- In rare cases it is possible that the rims touch minimal the brake caliper, then you can simply use spacers.
>> Now directly to spacers << - Install the adapter with the necessary components and then check if new brake lines are required. Because, depending on the vehicle, the lines may be too short or the line tips may not suitable. We advise you to change to steel braided brake line because of the quality and technical advantage. Specifically for this, we have developed an online brake line configurator, where you can assemble the type of steel braided brake lines you want.
Click here to go to the >> configure steel braided brake lines << - Always use the hand brake cable of the installed brake caliper. So sometimes you have to modify / adapt the new handbrake cable. For conversions, where the original caliper is used and the handbrake cable can be used, you may need to pull the cable without any other fittings (ie directly) to compensate for the long distance due to the large diameter of the large brake discs.
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Login
8 April 2023 06:55
Robert N
Verarbeitung: 3 Versand: 1+
12 January 2022 19:34
Ferry V
Past precies. En makkelijk te installeren AANRADER!
5 August 2020 10:39
Martin H
ok
18 August 2019 10:38
Sven T
Top Ware. Kann ich nur weiter empfehlen.
19 March 2019 12:00
Cristian P
alles ok
27 September 2018 20:46
Werner W
weil ich dazu aufgefordert wurde, obwohl ich die Teile noch nicht verbaut habe und dies auch an epytec gemailt habe!
18 September 2018 10:04
Michel L
Good product and quality. Easy to assemble.
27 May 2018 07:56
Achim S
Perfekte Abwicklung!
13 May 2018 18:01
Achim S
Top Ware und top Abwicklung!
12 April 2018 12:39
Steeve evrard P
super très bonne qualité
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: