Lightened Flywheel VW Polo 6N 1.4 1.6 L 16V Caddy 2 Seat Ibiza Cordoba 3,8 kg
- ✓ 1.4l, 1.6l 16V engines
- ✓ 200 clutch
- ✓ lightens 3.5 kg
€226.33*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Lightened high-strength flywheel made of chrome molybdenum
Suitable for all following engines with 200mm clutch:
- 1,4l, 1,6l 16V build in VW Polo, VW Caddy 2, VW Caddy 2, Seat Arosa, Seat Cordoba, Seat Ibiza
Suitable for all following gearboxes:
- 5-speed gearbox (the flywheel article 769 is suitable for 6-speed gearbox)
Thanks to additional drillings, now only 3,8 kg with the same quality!
Below in the suitable accessories you will find the Sachs Performance clutch pressure plate you need. You can also choose between the matching organic or racing Sachs Performance clutch disc.
Advantages of our lightened flywheel:
- our flywheel weighs only 3.8 kg, the standard wheel over 6.3 kg
- all our flywheels are made of chrome moly steel with quality G 1.75, extremely suitable for high-speed motors
- recognized for unlimited HP
- significantly better acceleration due to less inertia
- the engine runs faster, no loss of performance.
- suitable for motorsports, racing or serial vehicles
- lower fuel consumption
- significant reduction of the turbo lag
- precision balancing, bearings are less affected, finely balanced according to DIN ISO 1940
- including ring gear
- suitable for either a standard clutch or a high-performance clutch
- Our flywheels are registration-free as they have no direct effect on the actual performance.
Delivery:
- 1x lightened high-strength flywheel made of chrome molybdenum for all 1,4l 1,6l 16V engines in models VW Polo, VW Caddy 2, VW Caddy 2, Seat Arosa, Seat Cordoba, Seat Ibiza.
- Installation instructions
Our lightened flywheels are registration-free and therefore do not need to be registered.
Login
13 July 2024 10:49
Geoffrey T
Parfait ! 👍🏻
23 December 2024 19:23
danielr2770
Alles super gerne wieder
- Which screws can be used?
The original bolts can be reinstalled.
- Which clutch can be used with the Epytec flywheels?
You can continue to use the original clutch or an identical Sport / Performance clutch. Please check with the clutch manufacturer whether these are of the same design as the originals. If this is the case, then it will also fit 100%
- What is the friction coefficient of the flywheel?
In principle, the friction coefficient can be assumed to be at least the same as that of the original cast disc. Due to the higher alloyed steel, our pulleys are slightly better than the original cast pulley. Of course, the material of the friction disk also has a major influence here; this must be checked with the manufacturer of the friction disk
- What material are the flywheels made of?
The flywheel is made of 16MnCr (chromium molybdenum) steel, which means it has a density of 7.76 kg/dm³
- Does the flywheel have a TDC marking and other markings for the ignition?
The flywheel has no TDC marking, only the pin on the back, just like the original flywheel. Tip: To adopt the TDC marking, the original flywheel must be turned to the TDC point before disassembly and the new flywheel must be marked in exactly this position.
- Does the flywheel have the default unbalance or is it balanced to zero?
The flywheel is supplied with the default unbalance. Unbalance can be created as follows! We first balance the pulley to 0, then apply a test mass at the specified point, which corresponds exactly to the unbalance. The pulley is then balanced to 0 again with the test mass. If you now remove the test mass, you have exactly the specified unbalance.
- Do we only sell the ring gear / gearwheel of the flywheels?
No, we can only sell the flywheels complete.
- Why do I have to run in my clutch?
The principle of a clutch is similar to that of a brake system. The different materials / surfaces must first adapt to each other. This happens through friction. With standard clutches or organic linings, this happens relatively quickly, as the lining material is "softer" than with sintered metal linings.
- ✓ Reinforced version
- ✓ VW Polo 86c G40
- ✓ 325mm diameter
- ✓ 1.4l,1.6l, 16V engine
- ✓ 200mm clutch
- ✓ 250NM torque
- ✓ VW Polo 86c G40 1.3l engine
- ✓ 250NM torque
- ✓ hub profile: 18.3x20.4-24N
- ✓ VW Polo 86c G40 1.3l engine
- ✓ 250NM torque
- ✓ hub profile: 18.3x20.4-24N
- ✓ 1.4l,1.6l, 16V engine
- ✓ 200mm clutch
- ✓ 225NM torque