Brake caliper adapter VW Golf 7 8 Seat Leon Audi A3 Cupra Leon Skoda Audi RS4 R8 8-piston brake caliper 355x32mm brake disc Opel Insignia
- ✓ 355x32 00569132 Opel Insignia OPC brake disc
- ✓ 8-piston 8E0615107 / 8E0615108 RS4 B7 / R8 brake caliper
- ✓ front axle
£254.50*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Brake caliper adapter for front axle of Golf 7 8 Audi A3 8V etc. to the 8-piston brake calipers of Audi R8/RS4/TTRS in conjunction with the Opel Insignia OPC brake discs 355x32mm
The adapters are suitable for the following vehicles:
- Audi A3 8V
- Audi A3 Cabriolet 8V7
- Audi A3 Sportsback 8YA
- Cupra Formentor KM7
- Cupra Leon KL1
- Cupra Leon Sportstourer KL8
- Seat Leon
- Seat Leon Sportstourer KL8
- Seat Leon ST 5F8
- Skoda Octavia III
- Skoda Octavia IV
- Skoda Superb III 3V3
- VW Arteon 3H7
- VW Golf Sportsvan AM1
- VW Golf 7 5G1
- VW Golf 8 CD1
- VW Passat 3G2
Advantages of this brake system:
- Extreme deceleration values also in conjunction with our rear axle brake system
- The material certificate included in the scope of delivery can also be used to enable registration by individual approval for series vehicles.
- Fits directly on the above-mentioned models and can therefore be easily restored to their original condition at any time
- Our EPYTEC brake caliper adapters do not require you to send in your standard parts, no re-welding, re-milling or re-drilling.
Required components:
- brake calipers: Original RS4 B7 / R8 8 piston Brembo (20767502) Brake callipers Brake caliper left part no: 8E0615107 / 3D0615107A Brake caliper right part no: 8E0615108 / 3D0615108A
- Brake discs from Opel Insignia OPC 355x32, part no: 00569132
- brake disc, the bolt circle must be re-drilled. (Can also be done in-house)
Scope of delivery:
- 2x Brake caliper adapter for Golf 7 8 Audi A3 8V etc.
- High-strength screw set
- Material certificate
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information:
- ✓ Length: 63cm
- ✓ M10x1 outside 45° curved
- ✓ M10x1 inside straight
- ✓ 355x32
- ✓ 67.4mm centering
- ✓ 50mm height
- ✓ Registration-free
- ✓ Yellowstuff sports surface
- ✓ temperature up to 900°C
- ✓ Registration-free
- ✓ Redstuff ceramic covering
- ✓ temperature up to 750°C
- ✓ Racing brake fluid
- ✓ Reduction in brake fading
- ✓ improved pedal feel
- ✓ optimized paste for brake systems
- ✓ correct viscosity
- ✓ no squeaking
- ✓ 355x32
- ✓ 67mm centering
- ✓ 50mm height