Opel Vectra C GTS 16V Signum 0.5 Degree Camber Correction Adjustement Plates V6 Turbo
- ✓ camber correction plates for installation on rear axle. Allows a perfect camber adjustment on your vehicle, positive 0,5°
€113.67*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
⚠️ Important Notice:
This item is produced exclusively upon request. As it is a made-to-order special production based on demand, there is no right of withdrawal pursuant to § 312g (2) No. 1 of the German Civil Code (BGB).
Therefore, returns or exchanges are excluded.
Kit of camber correction / adjustment plates for rear axle. Makes possible a camber correction / ajustement.
Thanks to our plates with positive 0.5°, you can modify the rear camber. Ideal for lowering of the rear axle and for correcting the angle defect if the tires are worn out only on one side.
Our plates are mounted between the pivot of the axle stub and the axle. Quick and easy assembly. The wheels are then moved 3mm outwards. The plates are manufactured with high precision.
Its are made of steel and completely galvanized. Maximum anticorrosive protection and good optics.
Suitable for the following models:
- Opel Vectra C and Signum models , for bearing und wheel hub with manufacturing number: 1604 314
Delivery:
- 2x plates, right and left , positive 0.5°
Login
14 October 2018 17:46
vectrakanger
alles bestens gelaufen
9 February 2018 09:30
xpraptile04
Top Ware, superschnelle Lieferung, weiter so und vielen Dank nochmal!!! Perfekt!
5 January 2021 11:16
calibra-rot
Alles perfekt ! Gerne wieder
19 July 2018 00:21
Christian F
Very good! Fast delivery and good product! Thanks Christian
12 July 2023 06:12
Thorsten K
Sehr gutes Produkt lässt sich sehr gut verarbeiten passt perfekt
18 November 2022 09:07
djdee1381984
Sehr schnell bestens zu empfehlen.
22 December 2020 16:35
schmausi490
Super Ware, super schneller Versand, gerne wieder !!!
17 June 2020 17:35
dannyboy8624
Ware super,sehr zufrieden,super Ebayer,gerne wieder,Empfehlung 👍
24 December 2021 17:25
blauerhund7
>>> alles bestens
29 September 2018 16:29
acitburn2000
ware top schnell gerne wieder
- Does the ABS still function after installing the camber correction?
Yes, basically the ABS will continue to function after installing a camber correction. The important thing is: If you significantly change the camber, the geometry between the ABS sensor and the ABS ring (impulse ring) can shift in such a way that the sensor no longer operates optimally "at the correct angle" or parallel to the ring.
Why can there be problems?
The ABS sensor reads the ABS ring with a defined distance and alignment angle. With a significant camber change (often from about 1°, depending on the vehicle and axle design), it can happen that:
the sensor no longer lines up correctly, or
the air gap between the sensor and the ring is no longer within the target range.
Then the ABS can basically continue to work, but there can be, for example, ABS/ESP warning messages, sporadic interventions, or error memory entries.
What needs to be done then?
If something like this occurs, a small adjustment is usually sufficient:
Slightly correct the position of the ABS sensor (e.g., slightly reposition/align it on the mount)
Check seating and attachment (sensor must be flat and securely seated)
Check the air gap (not rubbing, not too large)
Then it is best to read/clear the error memory and take a short test drive.
Practical Tip
After the conversion, it is recommended to have an axle alignment. If you are using camber values in the range > 1°, it is advisable to check the ABS sensor area directly so that no surprises arise later.
- Do I need longer screws or can the old ones remain.
With Epytec camber correction plates, you can continue to use the original screws up to +-2°. For camber correction plates over 2°, we recommend slightly sanding a washer and placing it under the screw head so that it continues to sit flush on the camber correction plate. Of course, if the camber correction plate is thicker, new screws may be needed directly.
- Can camber correction plates be installed on drum brakes?
Yes, this is possible provided that a stub axle is installed on the rear axle. In this case, our Epytec camber correction plates can also be easily mounted on drum brakes. The functionality and installation are largely the same as for vehicles with disc brakes.
It is important that the mounting points of the stub axle match the execution of the camber correction plates.
| Motor | Motorcode |
|---|---|
| 2.2 DTi 16V | Z02|117PS(86KW) |
| Motor | Motorcode |
|---|---|
| 1.8 16V | Z02|110PS(81KW) |
| Motor | Motorcode |
|---|---|
| 2.2 DTi 16V | Z02|117PS(86KW) |
| Motor | Motorcode |
|---|---|
| 1.8 16V | Z02|110PS(81KW) |
- ✓ 345x30 93188445 Opel Vectra C OPC brake disc
- ✓ 4-piston 20A42503 / 20A42504 Renault Megane 3 RS brake caliper
- ✓ front axle