lightened flywheel Opel Omega X25XE X20XE X30XE V6 Kadett Corsa Astra Vectra Ascona
€339.00*
- Einfache TÜV Eintragung
- Qualität Made in Germany
- Faire Preise ohne Zwischenhandel, du kaufst direkt beim Hersteller und Enwickler des Produktes
- Weltweit Nr 1 in Sachen Tuning Adapter
- 15 Jahre Expertenwissen
- 10 Jahre Garantie
Erleichterte hochfeste Chrom Molybdän Schwungscheibe, passend für alle Opel X25XE X20XE X30XE V6 Motoren und RWD. mit 228 mm und 240 mm Kupplungsdurchmesser.
Vorteile unserer erleichterten Schwungscheibe:
- unsere Schwungscheibe wiegt nur 8,2 kg die Serienscheibe über 12,0 kg
- alle unsere Schwungscheiben sind aus Chrom Moly Stahl mit der Güteklassen G 1,75 für Hochdrehzahlmotoren geeignet
- zugelassen bis unbegrenzte PS Zahl
- deutlich bessere Beschleunigung durch weniger Schwungmasse
- Motor dreht schneller hoch, kein Leistungsloch mehr
- geeignet für Motorsport,Rennsport oder Serienfahrzeuge
- geringerer Spritverbrauch
- deutliche Verringerung des Turbo Loches
- präzise Feinwuchtung garantiert geringere Belastung der Lager feingewuchtet nach DIN ISO 1940
- inklusive Starterkranz
- kann mit Standard-Kupplungen oder mit Performance-Kupplungen gefahren werden
- Made in Germany
Lieferumfang:
- 1x erleichterte Chrom Moly Schwungscheibe für alle Opel Omega Astra Calibra Vectra Kadett mit X25XE X20XE X30XE V6 Motoren
Diese Schwungscheibe ist wohl die leichteste Scheibe für diesen Motor auf dem Markt. Nicht passend für Diesel-Motoren
Login
- Which screws can be used?
The original bolts can be reinstalled.
- Which clutch can be used with the Epytec flywheels?
You can continue to use the original clutch or an identical Sport / Performance clutch. Please check with the clutch manufacturer whether these are of the same design as the originals. If this is the case, then it will also fit 100%
- What is the friction coefficient of the flywheel?
In principle, the friction coefficient can be assumed to be at least the same as that of the original cast disc. Due to the higher alloyed steel, our pulleys are slightly better than the original cast pulley. Of course, the material of the friction disk also has a major influence here; this must be checked with the manufacturer of the friction disk
- What material are the flywheels made of?
The flywheel is made of 16MnCr (chromium molybdenum) steel, which means it has a density of 7.76 kg/dm³
- Does the flywheel have a TDC marking and other markings for the ignition?
The flywheel has no TDC marking, only the pin on the back, just like the original flywheel. Tip: To adopt the TDC marking, the original flywheel must be turned to the TDC point before disassembly and the new flywheel must be marked in exactly this position.
- Does the flywheel have the default unbalance or is it balanced to zero?
The flywheel is supplied with the default unbalance. Unbalance can be created as follows! We first balance the pulley to 0, then apply a test mass at the specified point, which corresponds exactly to the unbalance. The pulley is then balanced to 0 again with the test mass. If you now remove the test mass, you have exactly the specified unbalance.
- Do we only sell the ring gear / gearwheel of the flywheels?
No, we can only sell the flywheels complete.
- Why do I have to run in my clutch?
The principle of a clutch is similar to that of a brake system. The different materials / surfaces must first adapt to each other. This happens through friction. With standard clutches or organic linings, this happens relatively quickly, as the lining material is "softer" than with sintered metal linings.
