Ford Focus RS MK2 Bremssatteladapter 375x36 Bremsscheibe Audi RS4 B9 6 Kolben Brembo Bremssattel Tuning Adapter
- ✓ 375x36 4M0615301AM Audi RS4 B brake disc
- ✓ 6-piston 8W0615107AL / 8W0615108AL Audi RS4 B9 brake caliper
- ✓ front axle
€299.86*
- Easy TÜV registration
- Quality Made in Germany
- Fair prices without middlemen you buy directly from the manufacturer and developer of the product
- Worldwide no. 1 in tuning adapters
- 15 years expert knowledge
- 10 years warranty
Bremssatteladapter für den Ford Focus RS auf die Bremsanlage vom Audi RS4 B9, 375x36mm Bremsscheibe in Verbindung mit dem 6-Kolben Brembo Bremssattel.
Die Adapter passen für folgende Fahrzeuge:
- Ford Focus II 2.5 RS
- Ford Focus II 2.5 RS 500
Vorteile dieser Bremsanlage:
- durch das im Lieferumfang enthaltene Materialzertifikat kann eine Eintragung per Einzelabnahme auch bei Serienfahrzeugen ermöglicht werden
- direkt passend an die oben genannten Modelle und daher jederzeit problemlos wieder in den Originalzustand rückrüstbar
- unsere EPYTEC Bremssattel Adapter erfordern keine Einsendung von Euren Serienteilen, kein Umschweißen, Umfräsen oder Umbohren.
Benötigte Komponenten:
- Audi RS4 B9 6-Kolben Bremssättel Teilenummer: 8W0615107AL / 8W0615108AL
- Bremsbeläge, Teilenummer: 8W0 698 151 AN
- Bremsscheiben vom Audi RS4 B9 375x36mm Teilenummer: 4M0615301AM
Lieferumfang:
- 2x Bremssatteladapter für den Ford Focus II 2.5 RS
- hochfestes Schraubenmaterial
- Materialzertifikat
Tips, information and advice:
- To improve ventilation of the brake system, we recommend removing the anchor plates/brake dust plates.
- For easy mounting of the rim, we recommend purchasing two of our wheel mounting aids at the same time >>go directly to the article here<<
- We cannot give you a generalised answer as to which rim size you can ride after your brake conversion. There are simply too many different wheel rims. For this reason, we have developed a template with which you can easily check whether the brake system kit fits under your rim. We have included a link to the template in the description. If your rim does not fit, you can simply use wheel spacers. >> Go directly to customised wheel spacers <<
- Install the adapter with the required components and then check whether new brake lines are required, as the old ones may not be long enough or the connection may not fit, depending on the model. Due to the significantly better efficiency, we recommend switching to steel braided lines. We have developed a steel braided line configurator especially for this function, which you can use to assemble and then install them according to your requirements. Click here for the steel flex configurator >> Configure steel flex brake line <<
- The handbrake cable must always be used from the installed calliper, which means that the new handbrake cable may have to be adjusted slightly. For conversions in which the original calliper is still used and the original handbrake cable can be used, you may have to route it more directly to compensate for the larger disc diameter and longer travel
Please note that our articles have been designed for racing and motorsport. Use in public road traffic usually requires an individual approval in accordance with § 21 StVZO by an officially recognised expert. Further information can be found under TÜV Süd. For the individual approval, we will provide you with an expert opinion or material certificate, if available.
Technical data:
Login
- Can I also use other brake discs as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: https://epytec.de/uk/custom-made-products/brake-technology/adapters-for-brake-systems
- Can I also use other brake calipers as specified in the required components?
No, unfortunately that is not possible. The reason is simply: all brake calipers have different heights and depths. If another brake disc is installed, the brake caliper would either not fit on the adapter or not run in the middle of the brake disc. But if you want to install a different brake caliper, we also have an option for you. You can have a custom-made product made for you, take a look at the following link for more information: