Spacer PCD Adapter 5x100 5x112 5x120 5x130 to Porsche Mercedes Audi BMW Rims 20mm

Brake caliper adapters with special hub / hub adapter for vehicles with 5x100 or 4x100 PCD in order to install rear brake caliper of Porsche 996 and Audi S3 8L / VW Golf MK4 R32, combined with the front 280mm G60 GTI 16V brake discs on the rear axle.In this case, the S3 R32 calipers have only function of hand brake. These are necessary because the Porsche calipers do not have the function of hand brake. Suitable for the following VW und Seat models: Golf MK1 (only with our axle pivot - see item 313 in our shop.) Golf MK2 MK3 + GTI+ VR6 Corrado Jetta Passat 35i Scirrocco Vento Polo 6N1 Seat Cordoba Seat Ibiza Seat Toledo Advantages of this brake system: high deceleration, also in conjunction with our rear axle braking system better performance supplied material certificate Technics: The Porsche calipers are mounted between the axle beam and the axle stub. The necessary screws are supplied. The adapters for the S3 / R32 caliper are mounted onto the original Golf MK2 /MK3 bracket. With our supplied hub spacers, the 280 mm brake discs are centered and screwed. The track is wider by about 16 mm per side.The inside of the hub spacer is manufactured like the originals and therefore the wheel bearing remains the same.Not permitted under the STVO (German Road Licensing Law). However, thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehiclesFor the rear axle, we offer brake adapters for conversion to the Porsche brake system, combined with the R32 brake discs. Visit our shop.For vehicles equipped with ABS, the ABS disc of all Golf MK3 models can be kept and adjusted exactly on our hub spacers. Required components: brake caliper: Porsche , reference: 996.352.421 + 996.352.422 rear axle: brake caliper with mounting brackets from Audi S3 8L or VW Golf R32 front 280mm brake discs from VR6. Total height: 28,5mm VAG reference : 1H0615301 brake disc PCD habe to be modified to 4x100 (service available from EPYTEC) Delivery: 2x special hubs / hub adapters with 5x100 or 4x100 PCD 2x brake caliper adapters high strength mounting screws material certificate

Wheel hub for PCD conversion to 5x112, rear axle In this wheel hub there are 2 bolt circles, once the 5x100 and additionally the 5x112 bolt circle. This has the advantage that the bolt circle can be used for both 5x112 rims and 5x100 rims without having to change the components. Suitable for the following VW and Seat models: Golf MK1 (only with our axle pivot pin, Epytec, in our online shop) Golf MK2 MK3 + GTI+ VR6 Corrado Jetta Passat 35i Scirrocco Vento Polo 6N1 Seat Cordoba Seat Ibiza Seat Toledo If you want to convert your car to 5x112 PCD, here is the perfect solution. For the front axle, we recommend our matching wheel hubs with 5x112 bolt circle. (item number: APA162 click here)This hub is perfect for rear brake system conversion to larger discs, and the original wheel bearing can be used. Advantages:  no track enlargement. No modifications at the wheel arch/housing. Two bolt circles 5x100 and 5x112 so both can be used on the car. 100% fit. Based on original parts. the 5x112mm wheel hubs are equipped with M14x1.5 thread. Thus, the Audi and VW rims can be mounted with the original wheel bolts it is possible to register your purchase even for series vehicles by TÜV (German Technical Inspection Agency). But not permitted by STVO (German Road Licensing Law) The ABS can still be used as original. The original brake discs / wheel hubs are used as a basis, which have been subsequently extended to a PCD by a special method. Delivery: 2x wheel hubs for conversion to 5x112 PCD with M14x1.5 thread 

Fine drive / transmission shaft for many VW and Seat models. Absolutely necessary when lowering! The shaft is manufactured in one piece and is a complete drive shaft. Suitable for the following vehicles: Golf MK3 Golf VR6 Golf MK4 Cabrio 1E7 2,0  Vento Polo 9N Thanks to our thin and extremely stable transmission / drive shaft, you avoid many problems at the body that usually appear during a chassis lowering. With the installation of our drive shaft, you avoid many modifications and you save time.It is important that when installing the new drive shaft, no excess pressure is created in the sleeve. In our installation instructions you can see how to prevent this (click here). Technical data: assembly side: front axle right length:; 768,0 mm thread: M20x1.5 drilling-Ø: 8,2 mm PCD-Ø: 86 mm joint diameter, differential side: 100 mm number of drill holes: 6 external toothing wheel side: 36 chassis: for vehicles with low-profile chassis joint diameter wheel side: 90,0 mm Delivery: 1x fine thin drive / transmssion shaft for Golf MK3, Golf MK4, VR6, Vento (with all parts, see picture) Our drive shafts are registration-free and therefore do not have to be registered.

High-strength spacer  / PCD adapter suitable for Audi, VW, Seat, Skoda with 5x100 PCD and a hub centering dimension of 57,10mm at the wheel hub. 3 different PCD are on the plates: 5x112 5x120 5x130 Thanks to these spacers / adapters, all Audi, Mercedes, BMW and Porsche rims can be installed. The major advantage is that at each change of rims, you do not need to change the adapter / spacer. You can thus drive with Porsche rims in summer and BMW rims in winter. At each change of rims, you do not need to install a new adapter plate: Buy just once, and change several times, as good as it seems to you.In the installation instructions, you see how the whole thing is mounted. (click here) Due to the TÜV certificate (technical report) included in the scope of delivery, a registration can be carried out by individual acceptance. Technical data enlargement per wheel: 25mm enlargement per axle: 50mm hub centric inside VW: 57,10 mm hub centric outisde: 57,10 mm (can also be changed as desired with centric rings) thread in adapter plate for wheel bolts: M14 x 1,5 The adapter plates are made of high-strength aluminum and thanks to the material certificate delivered with the order, it is possible to register your unit purchase even for series vehicles. All screws supplied are also high-strength (10.9). Delivery: 2x spacers / adapter plates for one axle high-strength mounting screws (fine thread M14x1,5) on wheel hub 10.9  TÜV - certificate for registration Installation instructions This offer is only for one axle. For complete equipment of your vehicle,  please order 2 times. The article is also available with a thickness of 20mm. This allows you to compose the kit with the required thickness.

Gearbox cradle for gearbox exchange. For installation of gearbox typ 02M with 6 gears standard to mount from the R32 / V6 to the 1.8T or VR6 or 16V engine in the Golf 2 3 Passat Corrado Jetta Vento. Due to the stable construction and the accuracy of fit, the gearbox holder can be attached to the original bracket, which means that a precise fit of the gearbox can be guaranteed. This means that no welding is required on the body, which saves you a lot of time during the conversion.  Scope of delivery: 1x gearbox cradle on 02M / R32 V6 1.8T 6-speed gearbox DRP DQB DXW 1x gearbox cradle for stabilization of electic starter Certificate of material Installation instructions

High-strength wheel spacer / PCD Adapter suitable for all VW with PCD 4x100 and hub centric 57,10mm. Thanks to this adapter, all BMW rims with 72,6mm diameter (also BBS RS), compatible with a 5x120mm PCD, can be mounted. enlargement per wheel: 20mm enlargement per axle: 40mm internal hub centric VW: 57,10mm external hub centric BMW: 72,60mm screw thread on adapter: M14 x 1,5 All components are made of high quality aluminum. All screws provided are high-strength (10.9). Description: The adapter is fixed with 3 screws on the hub. The supplied eccentric bolt is fixed into the fourth drilling hole and oriented in such a way that the offset hole adjusts to the PCD. The rim is fixed with the 5 screws. By screwing the last screw into the eccentric bolt, the eccentric bolt automatically tightens and is fixed.In the installation instructions, you see how the whole thing is mounted. (click here) Due to the TÜV certificate (technical report) included in the scope of delivery, a registration can be carried out by individual acceptance. Delivery:  2x adapters / spacers for one axle 2x high-strength eccentric bolts complete mounting screws set, high-strength (10.9) TÜV - certificate for registration Installation instructions This offer is only for one axle. For a complete equipment of your vehicle, please order 2 times. The item is also available with the thickness of your choice. You can thus compose the kit with the required thickness.

Exclusive and individual bolt circle adapters / track extensions according to your wishes There is such a large selection of rims that there are almost never the right adapter plates to fit your vehicle. This is over now! With our configurator, we offer you the possibility to put together bolt circle adapters and wheel spacers according to your desired dimensions. Facts and scope of delivery: All plates are made of high-strength aircraft aluminum and are delivered with engraving on the plate and a technical certificate from TÜV (technical report) delivered. This allows registration by individual acceptance. The scope of delivery is regulated by the number of pieces you choose (selected number of pieces 1 piece = 1 plate and the necessary mounting screws to fix the plate to the scar). The mounting screws to fix the bolt circle adapters to the vehicle are delivered in such a way that the thread looks 20mm out of the plate. Please check if the length is sufficient so that the screw goes completely through the wheel hub and engages in all threads. Realized customer projects:Here is a selection for you of how customers have used the configurator to mount their dream rim on their vehicle or what is possible with our bolt circle adapters. Example on a Porsche rim, click here. Example of a bolt circle adapter on an offroadbuggy, click here. Better cornering stability for a trailer, learn more. And this is how it works: Just select your vehicle below. We make a pre-selection of vehicle data which are listed in our database. Some fields are already filled out automatically. If your vehicle is not listed or you have a motorbike or quad you can also make the selection manually. You can choose the bolt circle adapter/track width from 20mm thickness per side in 1mm steps. This is especially useful if you want to achieve a maximum width of your vehicle. With this you are no longer bound to straight dimensions. When you have filled out all required fields you can put your desired quantity into the shopping cart and pay there. We manufacture all adapter plates with thread for the rims, so that the rims can always be fixed with wheel bolts. Important Info:We manufacture all adapter plates with thread for the rims, so that the rims can always be fastened with wheel bolts and not with stud and no longer with wheel nuts as with your vehicle: The plates are clearly more favorable in the production and thus for you more favorably. With defective wheel bolts, the change is an enormous effort. The plate must be completely dismantled and the knurled bolt pressed out. This is not necessary for wheel bolts. Just order a new screw and you are done! You have a much larger selection of wheel bolts for your desired rim, the selection of wheel nuts is much smaller. Developed exclusively for alloy wheels, they offer a customised fit and optimum performance. With an impressive load capacity of up to 850 kg/wheel, our bolt circle adapters set new standards in load capacity. Please note that they are not suitable for steel rims. Configure your bolt circle adapters now for the highest quality in your conversion

Who wants to finally drive with 5x100 rims, is here just right.Complete conversion kit for front and rear axle to drive with rims PCD / Pitch Circle Diameter 5x100 on Golf MK2.Who would like to keep the brake system on his first original, but would still like to install 5x100 rims, has found the right kit here.This is probably the best alternative to our PCD adapters, because the track does not become wider.Suitable for all Golf MK1 and Jetta 2  with solid brake discs on the front axle, 239x10mm.  Advantages:  no PCD adapter necessary directly to use. No drilling of the brake discs. wheel arches do not necessarily have to be pulled (of course depending on the width of the rim) Delivery: complete conversion kit for front and rear axle on Golf MK2 to drive with rims PCD / Pitch Circle Diameter 5x100 and complete brake system with wheel bearing etc. (see picture)

Control arm suspension / wishbone with bushing, axle joint, and screws. Left and right, front axle for Golf MK4 1.6 16V, 1.9 TDI 4 motion, Audi A3 1.6, etc. criteriondetail quantity unit kit steering technics contral arm / wishbone supplementary item / info 2   with lock screw set assembly side front axle lon both sides assembly side bottom required quantity 1 Suitable manufacturer reference numbers:: 1J0 407 151A 1J0 407 151B 1J0 407 151C  Delivery: 1x wishbone, left with bushs and axle joint 1x wishbone, right with bushs and axle joint

Control arm suspension / wishbone, front axle, and tie / steering rods and screws, for Golf MK4 1.6 16V, 1.9 TDI 4 motion, Audi A3 1.6, etc. criteriondetail quantity unit kit steering technics contral arm / wishbone supplementary item / info 2   with lock screw set assembly side front axle lon both sides assembly side bottom supplementary item / info 2   with tie / steering rods required quantity 1 Suitable manufacturer reference numbers: 1J0 411 315B 1J0 411 315C 1J0 411 315 J  Delivery: 1x wishbone, left with bushs and axle joint 1x wishbone, right with bushs and axle joint 2x tie / steering rods

Control arm suspension / wishbone with bushing, axle joint, steering bar / rod, track rod and screws for Golf MK4 1.6 16V, 1.9 TDI 4 motion, Audi A3 1.6, etc. criteriondetail quantity unit Kit steering technics contral arm / wiscbone supplementary item / info 2   with lock screw set assembly side front axle left assembly side front axle right supplementary item / info 2 with steering rod / bar Steering with track rod end supplementary item / info 2 mit axle joint required quantity 1 Suitable manufacturer reference numbers: 1J0 422 804B 1J0 422 804H Delivery: 1x wischbone, left 1x wischbone, right 2x steering bars / rods 2x track rod ends

Do you want to avoid engine damage' Then we have the right one for you! Our baffle plate EPYTEC made of 1.5mm thick steeli s laser precision cut and fits perfectly into all 1.6L-2.0L G60 16V and 16Turbo oil pans.The plates are absolutely  necessary if you like fast driving in the curves without your engine being damaged. By welding these plates into your pan / sump, you will prevent the oil from foaming / swelling. And youcan prevent that air enters in  the circuit. Another advantage is the additional stability of the oil pan. This can give just the necessary safety when the oil pan is sometimes unstable. Suitable foor all 1,6l-2,0l engines from VW with the following engine classification code : PG RP ABF 9A ABS PF PB KR PL all 827 engine blocks Delivery: 4x baffle plates (complete KIT) made of 1.5mm thick steel for all G60 16V 16 Turbo oil pan

Engine and gearbox mounting bracket kit for conversion to 02M/ R32 V6 1,8T 6-speed transmission, combined with the Golf 4VR6 R32 engine in Golf MK2, MK3, Vento Due to the stable construction and the accuracy of adjustment, the bracket set can be fixed to the original holder/support, which means that an absolute fit of the transmission can be guaranteed. No welding on the body is necessary, which saves a lot of time when converting your vehicle.The engine and gearbox mounting brackets are supplied galvanized, which provides the best protection against corrosion.If the front engine holder is on the radiator cap, there simply has to be another cover on the flat one so that the holder can be fitted cleanly. The cooling cap from the Audi with the 2.5 TDI engine can be used here. Part number: 059 117 061 Advantages: the bracket creates an optimal center of gravity stable system all parts are CNC manufaktured top german quality product excellent corrosion protection. All parts are supplied galvanized. 100% fitting Delivery: 1x engine and gearbox mounting bracket kit for conversion to 02M/ R32 V6 1,8T 6-speed transmission, combined with the Golf 4 VR6 R32 engine in Golf MK2, MK3, Vento material certificate