Hub Centric Ring VW Bus T3 from 60.00 to 68.00 mm Audi Brake Disc

Exclusive and individual: length, color and connections / tips are available according to your choice. When converting to a better and larger brake system, standard brake lines are usually too short. From us, we offer steel braided brake lines in the length of your choice and the connections / tips of your choice. Thus, during a conversion of your vehicle, you have the possibility to place the brake lines according to your wishes. The brake lines have not only a better optics, but also a steel sheath that avoids a loss of pressure. Thus, the pressure point during braking can be much better controlled. Advantages compared to original brake lines: no loss of pressure when braking. Exact pressure point  easy assembly. The original line is simply replaced by the braided steel line no swelling as with rubber lines cost savings, because the braided steel lines do not need to be changed every 3 or 5 years shorter braking protection against the rodents material certificate great optic >>Here you can download and print out the appropriate parts certificate.<<

Brake caliper adapter to convert the T3 BUS to ventilated 312x25 brake discs with Audi A6 calipersAn independent conversion description from one of our customers can be found here: https://schrauberlaube.de/'page_id=25899 Advantages of this brake system: Top deceleration values no more overheating and fading of the brakes Very cheap procurement of the components brake calipers used from 49.- € new brake discs from 70.- € The material certificate included in the scope of delivery enables entry by individual acceptance even for series vehicles Quick and easy assembly possible with the supplied wheel hubs and screws! The wheel hubs supplied retain the standard VW bolt pattern and are identical to the original dimensions. This means that the wheel bearings can continue to be used and the track is only 6 mm wider on each side.  Required material for installation: Brake discs 312x25 mm Audi A4 quattro, Audi A6 e.g. 4B0 615 301 A Brake calipers Audi 100 / A6 C4 Girling / ATE 57 Part No: 4A0615123A / 4A0615124A (left, right) Brake caliper brackets that were installed with the 288 brake system.(are required because of the shorter design of the holder Part number: 3B0615125 At least 16 inch rims should be used Advice: This adapter is for all T3 buses built after 1986. Yours before 1986 require the >> adapter with article no. 466 << Scope of delivery: 2 high resistant adapter-plates 2x matching centering rings Certificate of material Complete set of high resistant srews 2x wheel hub for installation on front axle. Copy of the german document 'Fahrzeugschein' (equivalent with the English vehicle registration card). Proves the conformity of our product in Germany and simplifies authorization by authorities. stress analysis You can find installation instructions from a customer here: https://schrauberlaube.de/'page_id=25899 Here is an installation video from our customer, the steering knuckle is lightly machined as it is built before 1986, nothing needs to be machined on steering knuckles built after 1986, and a different brake caliper is used, hence the light machining:

We finally designed a brake caliper adapter that be installed on the T3 2WD bus (not Syncro) under the 15-inch rims. The adapters are mounted with 288x25 mm internally vented brake discs and with the Audi A6 calipers. Advantages: top deceleration system no longer warms up and no more fading very cheap components. you can find second-hand caliper from 49.- € / new from 70.-€ thanks to the material certificate supplied with the order, it is possible to register your purchase possible quick and easy assembly with the supplied mounting screws Required components: brake discs 288x25 mm Audi A4 Quattro, Audi A6 z.B. OE-number:4A0 615 301 C (VAG), 4A0 615 301 D (VAG), 4A0 615 301 E (VAG), 8E0 615 301 Q (VAG) other comparaison number:V10-80049 (VAICO), 100.1216.20 (ZIMMERMANN), 100.1216.70 (ZIMMERMANN)  bracke calipers Audi 100/A6 C4 Girling/ ATE 57  reference : 4A0615123A/4A0615124A (left, right) brake caliper brackets required for mounting the 288th brake system. Part No.:4A0615125A(required because of the shorter shape of these brackets) Brake Pads Original Parts NR VW 4A0698151A (We also have matching ones from EBC in our assortment (see accessories on this page below) Only suitable with the 14 inch axle of T3 (you can see it with the screws fixing the calipers. The thread should be 16 mm) Because of the thickness of the brake discs, the track is widened by 7mm for each side. Important!!! So that you can bleed the brake system cleanly, we recommend to mount the brake calipers reversed, i.e. to mount the left brake caliper on the right vehicle side and the right brake caliper on the left vehicle side. Delivery: adapter system for brake caliper complete set of high-strength screws for both sides hub centric rings for the discs matching wheel hubs material certificate stress analysis

We finally designed a brake caliper adapter that be installed on the T3 2WD bus (not Syncro) under the 15-inch rims. The adapters are mounted with 288x25 mm internally vented brake discs and with the Audi A6 calipers. Advantages: top deceleration the system no longer warms up and no more fading very cheap components. you can find second-hand caliper from 49.- € / new from 70.-€ thanks to the material certificate supplied with the order, it is possible to register your purchase quick and easy assembly with the supplied mounting screws Required components: Brake discs 288x25 mm Audi A4 Quattro, Audi A6 z.B. OE-number:4A0 615 301 C (VAG), 4A0 615 301 D (VAG), 4A0 615 301 E (VAG), 8E0 615 301 Q (VAG) other comparaison numbers :V10-80049 (VAICO), 100.1216.20 (ZIMMERMANN), 100.1216.70 (ZIMMERMANN)  bracke calipers Audi 100/A6 C4 Girling/ ATE 57  reference : 4A0615123A/4A0615124A (left, right) Brake caliper brackets required for installing the brake system 288.Part No.4A0615125A (required because of the shorter form of these brackets) Hubs that are also available in our shop, item number 341. A complete kit including hub is also available in our shop, number 657 Only suitable with the 15 inch axle of T3 (you can see it with the screws fixing the calipers. The thread should be 16 mm) Because of the thickness of the brake discs, the track is widened by 7mm for each side. Important!!!So that you can bleed the brake system cleanly, we recommend to mount the brake calipers reversed, i.e. to mount the left brake caliper on the right vehicle side and the right brake caliper on the left vehicle side. Delivery: 1x adapter system for brake caliper 1x complete set of high strength screws for both sides 2x hub centric rings for the discs material certificate

Brake caliper adapter to convert the T3 BUS on the front axle to ventilated 312x25mm brake discs with Audi A6 calipers. An independent conversion description from one of our customers can be found here:  https://schrauberlaube.de/'page_id=25899 Advantages of this brake system: The remaining fading on the original brake system is gone. Significantly better perfomance than the standard brake system. Very cheap procurement of the components. Brake calipers can be found used for as little as 49 euros/new for as little as 70 euros. TÜV registration possible with the supplied material certificate Quick and easy assembly possible with the supplied screws! Required material for installation: Brake discs 312x25 mm Audi A4 quattro, Audi A6 e.g. 4B0 615 301 A Brake calipers Audi 100 / A6 C4 Girling / ATE 57 Part No: 4A0615123A / 4A0615124A (left, right) Brake caliper brackets that were installed with the 288 brake system. Part number: 3B0615125 Wheel hubs (click here) to center the brake disc are also available in our shop.  Only suitable for the 14 inch axle of the T3 (to be found on the brake caliper fastening screw, this must have a 16mm thread) At least 16 inch rims should be used so that the diameter of the brake disc fits underneath Scope of delivery: 2x brake caliper adapters for VW T3 Bus matching centering rings Set of high-strength screws Vehicle registration copy for easier entry stress analysis You can find installation instructions from a customer here: https://schrauberlaube.de/'page_id=25899

Brake caliper adapter, front axle, on model T3 transporter for conversion to internally vented 312x25mm brake discs, combined with the Audi A6 calipers. Suitable for VW T3 transporter, manufactured before 1986 with M12 screw mount on the axle Advantages: top deceleration the system no longer warms up and no more fading very cheap components. You can find second-hand caliper from 49.- € / new from 70.-€ thanks to the material certificate supplied with the order, it is possible to register your purchase quick and easy assembly with the supplied mounting screws Required components: brake disc: Audi A4 quattro, Audi A6 312x25mm, reference e.g 4B0 615 301 A Brake caliper: Audi 100/A6 C4 Girling/ ATE 57, reference 4A0615123A + 4A0615124A (left,right) brake caliper mounting brackets that were installed with the 288 brake system (required because of the shorter design of the bracket) wheel hubs to center the brake disc are also available in our shop. since the screwing surface for the adapter is not level, it must be planned before installing the adapter so that the adapter fits properly. At least 16 inch rims should be used so that the diameter of the brake disc fits underneath Hint: This adapter is for all T3 bus before Bj 86 is yours after Bj 86 you need the >> adapter with the article no: 346 << Delivery: 2x brake caliper adapters for VW T3 transporter, manufactured before 1986 with M12 screw mount on the axle< matching centering rings set of high-strength screws

Brake caliper adapter, front axle, on model T3 bus/transporter for conversion to auf  internally ventred 347x30mm brake discs, combined with the Audi A6 brake calipers. Wheel hubs are supplied with this brake conversion, which retain the standard VW bolt circle /pitch circle (5x112) and are dimensionally identical. This means that the wheel bearings can continue to be used and the track is only 6 mm wider on each side. Advantages: top deceleration the system no longer warms up and no more fading very cheap components.  thanks to the material certificate supplied with the order, it is possible to register your purchase quick and easy assembly with the supplied mounting screws The wheel hubs supplied retain the standard VW bolt circle/pitch circle and are identical to the original dimensions. This means that the wheel bearings can continue to be used and the track is only 6 mm wider on each side. Required components: brake disc: Audi A6 347 x 30 mm, reference 4F0615301G brake caliper mit mounting bracket: ATE 981 + 982 from Audi A6 4F for 347mm disc, manufacture reference  8E0615124B wheel hubs to center around the brake disc are also available in our shop only fitting with the 14 inch axle of the T3 (to determine at the caliper mounting screw, this must have 16mm thread) Delivery: 2x brake caliper adapters, front axle, VW T3 bus / transporter / van high-strength mounting screws material certificate 2 x required wheel hubs matching centering rings

Brake caliper adapter including wheel hub, front axle, on model T3 transporter, for converstion to the internally ventilated 312x25mm brake discs, combined with the Audi A6 calipers. Suitable for VW T3 transporter built before 1986 with M12 screw mount on the axle Advantages of this brake system are: top deceleration system no longer warms up and no more fading very cheap components. you can find second-hand caliper from 49.- € / new from 70.-€ thanks to the material certificate supplied with the order, it is possible to register your purchase quick and easy assembly with the supplied mounting screws Required components: brake caliper: Audi 100/A6 C4 Girling/ ATE 57, reference 4A0615123A + 4A0615124A brake disc: Audi A4 quattro, Audi A6 312x25 mm, reference 4B0 615 301 A        brake caliper mounting brackets that were installed with the 288 brake system. (required because of the shorter design of the bracket) wheel hubs to center the brake disc are also available in our shop. At least 16 inch rims should be used so that the diameter of the brake disc fits. Delivery: 2x brake caliper adapters for VW T3 transporter before year 1986 with M12 screw mount on the axle matching centering rings including high-strength screw material 2x T3 transporter wheel hubs for the front axle.