EBC brake discs 280x22 Black-Dash front axle Seat VW Cordoba Ibiza 3 1.8 T 20V Cupra 2.0i

Who wants to finally drive with 5x100 rims, is here just right.Complete conversion kit for front and rear axle to drive with rims PCD / Pitch Circle Diameter 5x100 on Golf MK1.Who would like to keep the brake system on his first original, but would still like to install 5x100 rims, has found the right kit here.This is probably the best alternative to our PCD adapters, because the track does not become wider.Suitable for all Golf MK1 Caddy 14d  Jetta and  Scirocco with solid brake discs on the front axle, 239x10mm.  Advantages:  no PCD adapter necessary directly to use. No drilling of the brake discs. wheel arches do not necessarily have to be pulled (of course depending on the width of the rim) Delivery: complete conversion kit for front and rear axle to drive with rims PCD / Pitch Circle Diameter 5x100 and complete brake system with wheel bearing etc. (see picture)

Brake caliper adapter, front axle, to install the 280mm G60 brake discs, combined with the 4-pistons Porsche Boxter 986er brake caliper. Specially developed to be able to continue using 15-inch rims! Suitable for the following vehicles: Golf MK1 Golf MK1 Cabrio Caddy 14d Jetta 1 Scirocco Advantages of this brake system: high deceleration, also in conjunction with our rear axle braking system specially developed to be able to continue using 15-inch rims. brake discs with 4x100 PCD, Therefore, the original Dolf MK1 PCD can be maintained thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles.  directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems Our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling. We recommend the brake pads of the Porsche rear calipers, reference 996.352.421. These fit perfectly into the calipers and are perfect for the 280er brake discs! This allows the pads to fit perfectly to the 280 disc without any modification! Required components: brake caliper: 986er Porsche Boxter, reference 986.351.421 / 422   brake disc: VW Golf MK2/MK3 G60, 280x22,  reference 6KL 615 301 (only 100% fitting to the specified Porsche calipers) brake pads: from the rear calipers,  996.352.421 (these are smaller and look like the G60 brake pad surface) Delivery: 2x brake caliper adapters for VW Golf 1MK Caddy Scirocco , conversion to Porsche brake system 4x screws (10.9) 1x material certificate  The corresponding rear axle adapters for the conversion to 280er internally vented brake discs in combination with S3 brake calipers can be found in our shop.

Brake caliper adapter for front axle brake system to fix brake discs typ G60 diameter 280mm in combination with Porsche /Brembo 4 Piston brake calipers with bolt circle 4x100 on the following VW vehicles: VW Golf 2 und 3 VW Passat VW Corrado VW Jetta VW Polo Seat Toledo Required components:  Brake calipers Porsche 986 Porsche or Porsche 996 part nr.: 986.351.422 + 986.351.421 or oder 996.351.421+ 996.351.422 (written   on the caliper) (a successful conversion is only possibile with the before mentioned pieces!!!)  Brake discs typ Golf 2/3 G60 diameter 280x22mm  Advantages: Significantly better perfomance than the standard brake system. Furthermore wheel rims size 15" can be driven on some vehicles Components come from series production by VW The material certificate included in the scope of delivery enables entry by individual acceptance even for series vehicles Including complete screw material  Scope of delivery: 2x brake caliper adapter completely galvanized (see photo) Complete screw set high-strength. Certificate of material Stress analysis for better registration

Brake caliper adapter, front axle for Golf MK1 Polo G40 to convert to  G60 ATE / Girling 54 brake calipers, combined with the G60 280x22 brake discs. Suitable for the following models: Golf MK1 Golf MK1 Cabrio Caddy 14d Jetta 1 Scirocco 1/2 Passat Polo 1/2 Advantages of this brake system no more fading with the G60 brake system. thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems Our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling Required components: brake disc: G60 280x22 brake caliper: G60 ATE / Girling 54 brake caliper mounting bracket: G60 ( important: it must necessarily be the bracket of the 280 brake, and not of the 256. The 256 are too short) Tip: If you don't have the brake caliper carrier and brake calipers yet, we have the perfect solution for you here (click here).The brake caliper carriers were developed in such a way that you no longer have to install an adapter to install the G60 system on your vehicle.You can mount the brake calipers and brake caliper brackets directly on your vehicle. What is the difference between item number 216 and 142' The hole dimensions of the two tuning adapters are identical. We recommend always to install the article 216, because it is more stable. The tuning adapter 142 we have developed for the VW Polo axle, since this is slightly different in shape and the tuning adapter 216 can not be installed. Delivery: 2x brake caliper adapters copy of vehicle document to simplify the registration. high-strength mounting screws installation instructions material certificate

Brake caliper adapter with tailor-made wheel hub for rear axle brake system.For fixation of brake discs diameter 280mm from G60 VR6 GTI 16V normally used on front axle in combination with standard brake calipers from Golf 4 V6/R32 or Audi S3 8L year 99. Adapters are tailor-made for the following vehicles: Golf 1 (only after installation of our tailor-made pivot,that you can find in our product range) Golf 2 3 + GTI+ VR6 Corrado Jetta Passat 35i Scirrocco Vento Polo 6N1 Seat Cordoba Seat Ibiza Seat Toledo Depending on the vehicle the wheel hub will be delivered with 4 or 5 fixation holes.If you also need wheel hubs, we recommend ordering the complete set directly article 344There are 2 different installation positions for the brake caliper adapter, depending on which brake disc is installed. Advantages: Significantly better perfomance than the standard brake system. must have when increasing performance. Material certificate is included Inexpensive procurement of spare parts The material certificate included in the scope of delivery enables entry by individual acceptance even for series vehicles  Technical information: The 280 mm brake discs are centered and screwed on with our wheel hub (available in 4 and 5 holes depending on the model). The track widens by about 6-8mm per side. The wheel hubs are identical to the originals on the inside of the bearing. The original wheel bearings can therefore continue to be used. Suitable for the front axle, we offer you brake caliper adapters for conversion to the Porsche brake system in connection with the R32 brake disc. Look in our shop. Required components: Brake caliper left VW part number 8N0615423C, brake caliper right VW part number 8N0615424C, brake caliper bracket VW part number 8N0 615 425 B or painted in blue from the R32: 1J0 615 425 F. Brake disc: if 5 holes are driven: Golf 3 VR6 brake disc 280x22mm VW part number 1H0615301A pot depth 29mm when driving 4 holes: Golf 2 G60 brake disc 280x22mm VW part number 535615301 pot depth 40mm Scope of delivery: 2 high resistant adapter-plates  high-strength screw material Certificate of material  Stress analysis / FEM calculation for entry  In this kit the whell hubs are not included. See article nr.344

Brake caliper adapter, front axle, to install on models Golf MK1, Golf MK1 Cabrio, Caddy 14d, Jetta 1, Scirocco the 280mm brake disc of Golf MK2 G60, combined with the Audi S2 brake caliper. These adapters were developed by us NEW.Extra for the S2 Girling 60 brake calipers! Required components: brake discs front 280mm diameter Golf MK2 G60 (including Syncro), PassatG60 (including Syncro), CorradoG60 Brake calipers from the S2 Girling 60, part number: 895 615 124 A / 895 615 123 A Brake caliper carrier, part number: 447 615 125 Advantages of this brake system: even more powerful braking than with the conversion to G60 brake by double piston brake still usable with 15 inch. Wheel offset must be tested according to the rim. Spacers plates may have to be installed a registration for public traffic should not be a problem, provided it has been correctly and completely installed. directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems Delivery: 2x brake caliper adapters for Golf1, Golf 1Cabrio, Caddy 14d, Jetta 1, Scirocco 1x installation instructions with detailed picture material 1x material certificate Stress analysis for registration

Brake caliper adapter with special wheel hubs to drive the rear brake calipers from Golf 4 V6/R32 Audi S3 8L My.99 in combination with the front 280mm VR6 or G60 brake discs on the rear axle. Suitable for the following VW and Seat models: Golf 1 (only in combination with our Axle Stud -Article No. 313) Golf 2 3 + GTI+ VR6 Corrado Jetta Passat 35i Scirrocco Vento Polo 6N1 Seat  Cordoba Seat Ibiza Seat Toledo Technic: With the use of our wheel hub (available in 4 and 5 holes depending on the model) the 280mm brake discs are centred and bolted on.the track becomes wider by approx. 6-8mm per side. The wheel hubs are identical to the original wheel hubs on the inside, so the original wheel bearings can be used. There are 2 different installation positions of the brake caliper adapter, depending on which brake disc is installed.  Advantages of this brake system: Top deceleration values, no comparison to the conventional rear brake discs. a musthave for performance upgrades Material certificate is supplied Low-priced spare parts procurement                                                                                                                               The material certificate included in the scope of delivery enables registration by individual acceptance even for series production cars. With our EPYTEC wheel hubs the original rear Golf 2 3 wheel bearings can still be driven.  Suitable for the front axle we offer caliper adapters for a conversion to the Porsche brake system in connection with the R32 brake disc. Look in our shop.  Required components: Brake caliper left VW part number 8N0615423C, Brake caliper right VW part number 8N0615424C,  brake caliper holder VW part number 8N0 615 425 B or painted blue from R32: 1J0 615 425 F. Brake disc: if 5 hole is used: Golf 3 VR6 brake disc 280x22mm VW part number 1H0615301A pot depth 29mm if 4 hole is used: Golf 2 G60 brake disc 280x22mm VW part number 535615301 pot depth 40mm Scope of delivery: 2 pieces brake caliper adapter 2 pieces wheel hubs for mounting the brake discs  Material certificate Stress analysis / FEM calculation for registration

Brake caliper adapter, front axle, for Golf MK1, Golf MK1 Cabrio, Caddy 14d, Jetta 1, Scirocco to convert to 280 mm brake system from the following models: Golf 2 G60 (incl. Syncro) Passat G60 (incl. Syncro) Corrado G60 Combined with the Girling or Lucas 54 Sätteln und 280 mm brake discs. NEW: delivered in black color. Our caliper adapters are manufactured with a special method against corrosion, which guarantees best rust protection and abrasion resistance Advantages of this brake system: no more fading with G60 brake system .high deceleration, also in conjunction with our rear axle braking systemthanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehiclesdirectly fit to the above-mentioned models and therefore can always be restored to the original state without any problemsOur EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling Tip: If you don't have the brake caliper carrier and brake calipers yet, we have the perfect solution for you here article APA274 (click here).The brake caliper carriers were developed in such a way that you no longer have to install an adapter to install the G60 system on your vehicle.You can mount the brake calipers and brake caliper brackets directly on your vehicle. What is the difference between item number 216 and 142' The hole dimensions of the two tuning adapters are identical. We recommend always to install the article 216, because it is more stable. The tuning adapter 142 we have developed for the VW Polo axle, since this is slightly different in shape and the tuning adapter 216 can not be installed. Delivery: 2x brake caliper adapters, black, galvanized (high-strength steel) 4x srews (10.9) Installation instructions with detailed picture material copy of vehicle document to simplify the registration material certificate

Brake caliper adapter, front axle, for Golf MK1 serie to convert to 4-piston Porsche Boxter 986 brake calipers rear axle, combined with the 280mm G60 brake discs. Suitable for following vehicles: VW Golf MK1 VW Golf MK1 Cabrio Caddy 14d Jeta 1 Scirocco Polo g40 Advantages of this brake system: high deceleration, also in conjunction with our rear axle braking system 15 inch rims is possible brake disc with 4x100 PCD. Therefore, the original Golf MK1 PCD can be maintained. thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles directly fit to the above-mentioned models and therefore can always be restored to the original state without any problems Our EPYTEC brake caliper adapters do not require any sending of your serial parts, no welding, milling or drilling Required components: brake caliper: 986 Porsche Boxter , reference 986.352.421 / 422 (only 100% suitable for the mentioned Porsche calipers) brake disc: VW Golf MK2 / MK3 G60 280x22 , reference: 6KL 615 301 Delivery: 2x brake caliper adapters for VW Golf MK1 Caddy Scirocco to Porsche brake system high-strength mounting screws material certificate

Who wants to finally drive with 5x100 rims, is here just right.Complete conversion kit for front and rear axle to drive with rims PCD / Pitch Circle Diameter 5x100 on Golf MK1.Who would like to keep the brake system on his first original, but would still like to install 5x100 rims, has found the right kit here.This is probably the best alternative to our PCD adapters, because the track does not become wider.Suitable for all Golf MK1 Caddy 14d  Jetta and  Scirocco with solid brake discs on the front axle, 239x10mm.  Advantages:  no PCD adapter necessary directly to use. No drilling of the brake discs. wheel arches do not necessarily have to be pulled (of course depending on the width of the rim) Delivery: complete conversion kit for front and rear axle to drive with rims PCD / Pitch Circle Diameter 5x100 and complete brake system with wheel bearing etc. (see picture)

Brake caliper adapter, rear axle, on models Golf MK3 Corrado Syncro, for conversion to rear brake caliper from Golf MK4 V6/R32 Audi S3 8L YoC.99, combined with the brake discs, front, 280mm, G60. Suitable for the following models of VW and Seat, with Syncro axles: Golf MK2 Syncro Golf MK3 Syncro Corrado Syncro Passat 35i  Syncro Advantages of this brake system: top deceleration, without comparison with conventional brake discs better fading thanks to the internally vented discs better performance thanks to the material certificate supplied with the order, it is possible to register your purchase even for series vehicles For the front axle, we have in our shop brake caliper adapters for conversion to Porsche brake system, combined with R32 brake discs . Visit our shop. Required components: brake caliper: VW Golf R32 V6 or S3 VW , reference left 8N0615423C  right 8N0615424C brake caliper mounting bracket , reference 8N0615425B brake disc: Golf 2 G60 VW , reference 535 615 301 / important: total height 39,5mm Delivery: 2x brake caliper adapters complete screw kit material certificate