Skip to main content
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT
Simple registration for the technical inspection
QUALITY MADE IN GERMANY
DIRECT FROM THE MANUFACTURER
WORLD'S NR.1 TUNING ADAPTER
15 YEARS OF EXPERT KNOWLEDGE
FREEDOM: INSTALL WHAT YOU WANT

Installation instructions BMW 3 Series E46 weld-in panels Repair panels rear axle for cracks

Installation instructions for article 101 for the BMW E46 3 Series, for cracks on the rear axle. Here you can find out how to proceed step by step.

In the E46, cracks can occur in the rear axle mounts, regardless of body shape, engine type and year of manufacture. This can lead to the axle carrier tearing out. This is caused by barrel bearings that are too soft or have worn out over time, causing the axle to make excessive tilting movements during load changes and stressing the body to the point of cracking.
 
The reinforcement plates from Epytec.de can be installed to carry out a repair or counteract the problem. To do this, the axle carrier must be removed and it is advisable to work in pairs.

  • Remove the exhaust, cardan shaft and differential (otherwise the axle is very heavy)
  • Remove the brake callipers incl. carrier from the axle, disconnect the plug connections (ABS sensor, brake warning contact, etc.). Remove the lower damper bolts
  • Remove trailing arm bolts (3 on each side, mark position beforehand as the track is adjusted here)
  • Remove 2 nuts and 2 bolts from the rear axle carrier - Remove the fuel tank (not essential, but makes work easier and is safer when welding)

Welding the metal sheets :

Remove the 2 stud bolts and thoroughly polish all 4 points. Interrupt any cracks by drilling a small hole at the end of the crack and welding it shut

If necessary, adjust panels to the underbody.


Important!

Make sure a second person with a compressed air gun is in the car, underbody protection and interior panelling tend to catch fire here

Blech jeweils mit einem der Stehbolzen in Position bringen und anpunkten. Die Bleche sollten nicht am Stück durchgeschweißt werden. Dies führt sonst zur Versprödung des Bleches durch Überhitzung und man hätte eine neue Schwachstelle eingebaut. Ggf. im Pilgerschrittverfahren schweißen, um Wärmeeintrag gering zu halten. 

Die 2 kleinen Platten mit Löchern für den Höhenausgleich müssen unter dem Differentialträger verbaut werden. Sie können entweder verschweißt werden, oder beim Einbau der Achse später unterlegt werden.

Then treat the area generously with zinc spray. Once dry, seal with body sealant and spray over with underbody protection. Make sure that the contact surfaces of the barrel bearings are as even as possible.

Refit the axle beam:

It is strongly recommended to replace the old bearings with new ones, use PU bearings if necessary. 
Replacing the barrel bearings:  
Drill through the rubber all around with a 10 mm drill bit and a lot of "smack" until the aluminium bush in the centre can be knocked out. Then use a screwdriver and hammer to bend the outer bushing inwards at one point and knock the bushing out completely.
Refit everything and measure the vehicle.

The set also includes 2 square plates. These are needed if the axle mount is also to be welded to the inside of the body. To do this, cut out 2 square pieces from the inside.
The 3 original welding points can then be seen underneath. The sheet metal in between is cut out and the welding points are extended. The whole thing should be generously sprayed with cavity protection or similar to prevent corrosion. . 
The plates supplied are then welded back in to seal the holes. Do not apply too much heat, as the bearings underneath can be damaged if the axle has already been reinstalle








Copyright J. Wenzel

Here is the matching product for the installation instructions

Average rating of 4.7 out of 5 stars

BMW 3 Series E46 Welded Plate Repair Plate Rear Axle with Cracks
  • ✓ excellent fit
  • ✓ rear axle BMW E46
  • ✓ high stability

€53.83*
Item number: 101

Any questions or requests?

Then simply get in touch via our contact form (click here)

Tuning Adapter Topseller

Average rating of 4.9 out of 5 stars

Audi A3 S3 TT VW Polo 6R VW Golf MK4 Bora Porsche Brake Caliper Adapter
  • ✓ 323x28 1ML615301 Seat Leon Cupra R brake disc
  • ✓ 4-piston 955352421 / 955352422 Porsche Cayenne brake caliper
  • ✓ front axle

€155.28*
Item number: 596

Average rating of 4.9 out of 5 stars

Audi TT A3 S3 VW Golf Polo 6r WRC Brake Caliper Adapter Cayenne ZR17 Brake System 334x32
  • ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 R32 brake disc
  • ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne / VW Tuareg brake caliper
  • ✓ front axle

€148.46*
Item number: 403

Average rating of 4.8 out of 5 stars

BMW E30 Wheel Hub Conversion PCD 5x120 E36 E46 Adapter Spacer Front 5 Hole Hub
  • ✓ Conversion bolt circle 5x120
  • ✓ wheel hub E36 / E46
  • ✓ front axle

€105.75*
Item number: 126

Average rating of 4.5 out of 5 stars

Brake caliper adapter BMW 1 series 2 series 3 series 4 series F20 F21 F22 F23 F30 F31 F32 F33 F34 F36 convertible coupe BMW M2 M3 380x30 brake disc 4 piston brake caliper tuning adapter
  • ✓ 380x30 34112284809 34112284810 Brake disc
  • ✓ 4-piston F20 34116799465 34116799466 Brake calipers
  • ✓ front axle

€161.21*
Item number: 1108

Average rating of 4.9 out of 5 stars

Brake Caliper Adapter Porsche for Audi TT A3 S3 VW Golf Polo
  • ✓ 334x32 8N0615301B 1J0615301 R32 brake disc
  • ✓ 6-piston Z18 95535142153 / 95535142253 Cayenne brake caliper
  • ✓ front axle

€160.71*
Item number: 143

Average rating of 4.1 out of 5 stars

Brake Caliper Adapter VW T5 T6 Porsche Panamera 87mm Mercedes Benz Brake Disc 375x36 Front Axle
  • ✓ 375x36 1664210912 Mercedes Benz GL brake disc
  • ✓ 6-piston 7PP615149J / 7PP615150J Cayenne 958 GTS Panamera brake caliper
  • ✓ front axle

€214.39*
Item number: 942

Average rating of 4.9 out of 5 stars

Golf Corrado VR6 16V Brake calipers adapter R32 S3 TT 1,8T 312x25 334x32
  • ✓ 312x25 1J0615301AA 1J0615302A S3 / R32 brake disc
  • ✓ 1-piston 1J0615123E / 1J0615124E S3 / R32 brake caliper
  • ✓ front axle

€34.64*
Item number: 575

Average rating of 4.9 out of 5 stars

Golf MK1 Caddy Brake Caliper Adapter G60 S2 Adapter Brake System
  • ✓ 280x22 535615301 G60 brake disc
  • ✓ 1-piston Girling 54 443615124A / 443615123A brake caliper
  • ✓ front axle

€105.70*
Item number: 216

Average rating of 4.9 out of 5 stars

Mercedes Benz C63 W204 Brake System 390x36 AMG Brake Caliper Adapter 6-piston
  • ✓ 390x36 A2314211812 / A2314211812 Mercedes AMG C63 brake disc
  • ✓ 6-piston A2044214798 / A2044214898 Mercedes CLS 63 AMG brake caliper
  • ✓ Front axle

€214.97*
Item number: 890

Average rating of 4.9 out of 5 stars

VW Golf 3 Brake Caliper Adapter Porsche Vr6 GTI Passat 35 16V ZR17 ZL17 Front axle Brake System 334x32
  • ✓ 334x32 1J0615301AA 1J0615302 A Golf 4 brake disc
  • ✓ 6-piston 7L6615123T / 7L6615124T Porsche Cayenne/ VW Tuareg brake caliper
  • ✓ front axle

€133.47*
Item number: 284