Other products

• intake manifold conversion kit on BMW E36 2.8i models to install a manifold of BMW M50 M52 models.

• adapter plate engine starter TDI engine conversion
• VW T3 Bus/Synchro TDI starter Golf MK3 Bulli Britsche Doka 

• bush / spacer / washer/ adapter bushing to install the steering gear box from BMW E36, E46 and Z3 onto BMW E30  

• tension pulley adapter with pulley for VW Golf 1 Caddy 1,8T / 2,0 16V AGU , etc. Engine conversion

• drive shaft adapter for the VW T3 transporter to continue using the original drive shafts, also with the 012 Audi gearbox

• adapter plate for the fusebox / fuse box sheet plate for the Golf MK1 series. Conversion to 02A gearbox

• Adapter for conversion to single ignition coils for BMW E30 , E36 and Z3 with M42 and M44 engines

Adapter for conversion of your Audi 20V 7A engine.Allows installation of Bosch injection nozzles.

• repair plate for all 1.9 and 2.0 TDI engines installed in e.g. Golf MK4, Audi A3, VW Bora, Beetle, Seat, Skoda, and many more.

• is your door handle broken'
• with this repair set, we have the perfect solution. Repair once and no more problems for lifetime

• sensor adapter for oil pressure switch. Suitable for several engines BMW M50 M52 S50 S52, on models E34 E36 E39 E46 E38 Z3

• tension pulley adapter for VW Golf MK1 Caddy 1,8T / 2,0 16V AGU, etc. Engine conversion.

• adapter ring for the  Polo 9N wheel hub
• ABS Sensor ring Mark 20 from Golf MK4 can be taken over

• 1x 3mm reinforcing steel plate for underide protection, for VR6 oil sump/ pan, suitable for all  vehicles with VR6 engine, for example  Golf MK1 MK2 MK3 Corrado Vento, etc.

• connection reducer to radiator water inlet. Is required on Golf MK1 for conversin to VR6 / R32 engine

• seat damping for the driver and passenger seat on the BMW E36 Z3 with electronic seat adjustment

• clutch pin / clutch locking pin made of brass for all common BMW models such as e.g. E30 E46 E81 E88 and much more

• Golf MK1 Caddy Jetto Scirocco ABS, kit with adapter for sensor support / bracket in order to install ABS Mark 20 with Golf MK4 ABS sensor and ABS rings / washers 

• 1x assembly adapter for the VR6 engine

• anti-theft protection system for pedals on T2 T3 bus, also Syncro Doka Pritsche Bulli

The steel sheets need to be welded directly on the clutch release lever to avoid folding after installation of more resistant clutch or pressure plate.

• 2 hood supports / fasteners / hinges made of aluminium
• only 180 gr and the advantage that you will never have more rust and paint defects on the hinges

• Adapter for conversion to single ignition coils for the BMW E30, E36 and Z3 with M42 and M44 engines

• adapter plate for conversion to a double seat on the passenger side in the front of the VW T4 transporter

• hand brake cable adapter for conversion from R8 hand brake caliper to Golf MK3 MK4 hand brake cable 

• injection rail for conversion from 16V to G60 and turbo. Required for engine conversions with PL, KR, 9A and ABF to G60 and turbo engine block, combined with the standard intake manifold

• hollow screw / banjo screw adapter for oil cooler connection M50/52 on BMW E36 E39 Z3 models

Injection nozzle Adapter. For installation of injection nozzle from RS4 on S4 or S6 2.7 Biturbo.

• unibal suspension bearing for strut mount made of aluminium on models VW Golf Jetta Scirocco 1 and 2 Caddy 14d. Camber and caster angle adjustement

Adapter plates for the installation of the standard BMW M5 M6 throttle on the M30 engine.

• for Golf 5 series with 1,8T, 1,9TDI and R32 engines
• elevating  / lifting block engine with oil pan20mm

Extensible belt tightener.Allows installation on G60 / 16V engines. Replaces the original belt tightener of your vehicle.

Flat holder in stainless steel for fixation of belt tightener.Allows installation on G60 / 16V engines. Indispensable for all engine conversion on Golf 1 Caddy because of its form.

•  cover / closure plate made of aluminium to lock the original crankcase ventilation system for VW 1,8 l KR PL 16V engine

• BMW E30 Cabrio repair kit

• 1x universal joint shaft for servo steering VW Golf MK1 Cabrio

• completely new steering gear for the VW Golf MK1 / Cabrio / Jetta 1 / Scirocco
• hydraulic steering gear, incl. tie rod end and steering collar/sleeve

• conversion kit for the brake booster on BMW E30 model

• Spacer bolt for easy installation of the ignition coil adapter plate Article 257 for the BMW E30, E36 and Z3 with M42 and M44 engines