Other products
- clutch pin / clutch locking pin made of brass for all common BMW models such as e.g. E30 E46 E81 E88 and much more
Hexagonal coupling nut M8x30
Thread right
Galvanized
- conversion kit for brake booster on BMW E30 model for V8 conversion
- 1x hydraulic steering gear as shown including tie rods for your VW T3 transporter, platform, utility and T3 chassis
- completely new steering gear for the VW Golf MK1 / Cabrio / Jetta 1 / Scirocco
- hydraulic steering gear, incl. tie rod end and steering collar/sleeve
- 1x universal joint shaft for servo steering VW Golf MK1 Cabrio
- for VW transporter T5/T6 utility / platform, multivan T5/T6
- VW Golf MK4 Audi A3 2.3 V5 4motion
- steering gear, axle joint and track rod ends
- Adapter for conversion to single ignition coils for the BMW E30, E36 and Z3 with M42 and M44 engines
- adapter plate for conversion to a double seat on the passenger side in the front of the VW T4 transporter
- hand brake cable adapter for conversion from R8 hand brake caliper to Golf MK3 MK4 hand brake cable
- spacing plate / bush / bushing for brake caliper adapter
The steel sheets need to be welded directly on the clutch release lever to avoid folding after installation of more resistant clutch or pressure plate.
- closure / sealing / lock plate for conversion engine from 2,0l 16V VW to G60
Injection nozzle Adapter. For installation of injection nozzle from RS4 on S4 or S6 2.7 Biturbo.
- injection rail for conversion from 16V to G60 and turbo. Required for engine conversions with PL, KR, 9A and ABF to G60 and turbo engine block, combined with the standard intake manifold
- for Golf 5 series with 1,8T, 1,9TDI and R32 engines
- elevating / lifting block engine with oil pan20mm
Adapter for conversion of your Audi 20V 7A engine.Allows installation of Bosch injection nozzles.
- connection reducer to radiator water inlet. Is required on Golf MK1 for conversin to VR6 / R32 engine
- cover / closure plate made of aluminium to lock the original crankcase ventilation system for VW 1,8 l KR PL 16V engine
Extensible belt tightener.Allows installation on G60 / 16V engines. Replaces the original belt tightener of your vehicle.
- is your door handle broken'
- with this repair set, we have the perfect solution. Repair once and no more problems for lifetime
- 2 hood supports / fasteners / hinges made of aluminium
- only 180 gr and the advantage that you will never have more rust and paint defects on the hinges
Hexagonal coupling nut M8x30
Thread right
Galvanized
Hexagon nut self-locking M12
Ring non metallic (plastic)
Thread right
Galvanized
Zinc-plated press-in nut M06 with right hand thread
Hexagonal nut M08
Thread right
Galvanized
Hexagon thin nut M08
Thread left
Galvanized
- adapter plate for the fusebox / fuse box sheet plate for the Golf MK1 series. Conversion to 02A gearbox
- 1x assembly adapter for the VR6 engine
- repair plate for all 1.9 and 2.0 TDI engines installed in e.g. Golf MK4, Audi A3, VW Bora, Beetle, Seat, Skoda, and many more.
- conversion kit for the brake booster on BMW E30 model
- unibal suspension bearing for strut mount made of aluminium on models VW Golf Jetta Scirocco 1 and 2 Caddy 14d. Camber and caster angle adjustement
- drive shaft adapter for the VW T3 transporter to continue using the original drive shafts, also with the 012 Audi gearbox
- seat damping for the driver and passenger seat on the BMW E36 Z3 with electronic seat adjustment
- adapter ring for the Polo 9N wheel hub
- ABS Sensor ring Mark 20 from Golf MK4 can be taken over
- rear mounting side
- length: 1604mm
- brake type: disc brake
- VW Golf MK3 Vento Corrado
- 1x handbrake cable
- Golf MK1 Caddy Jetto Scirocco ABS, kit with adapter for sensor support / bracket in order to install ABS Mark 20 with Golf MK4 ABS sensor and ABS rings / washers
- Crankshaft ventilation cover VW 2.0l ABF 16V engine dry sump Golf Corrado